IBCcontrol F21075301 Скачать руководство пользователя страница 6

Страница: 6 / 16

MANUFACTURER'S DECLARATION

Manufacturer

IBC control AB

Brännerigatan 5 A, SE-263 37 Höganäs, Sweden

Product

Control unit for rotary heat exchanger

Type designation

MicroMax750

EU directive

applied to the

product

The manufacturer's declaration of conformity with the

requirements of the EMC Directive 2014/30/EU.

All control units are approved according to the

requirements of the EMC Directive 2014/30/EU and are

tested according to standard EN 61800-3:2004/A1:2012,

emission category C1 and immunity second environment.
All control units comply with the Low Voltage Directive

2014/35/EU, standard EN 61800-5-1:2007/A1:2017.
All control units are designed for installation in

environments subject to pollution degree 2.

This product also complies with RoHS Directive 2011/65/EU

including Commission Delegated Directive EU 2015/863.

Höganäs 2019-07-05

IBC control AB

Christer Persson

Содержание F21075301

















Результаты поиска

Содержание F21075301

Отзывы:

Похожие инструкции для F21075301

Бренды по названию

Популярные бренды

IBCcontrol F21075301, Руководство пользователя

Результаты поиска

Содержание F21075301

Отзывы:

Похожие инструкции для F21075301

Бренды по названию

Популярные бренды