IBC DC 15-95 Скачать руководство пользователя страница 50

Страница: 50 / 82

INSTALLATION AND OPERATION INSTRUCTIONS

2-6

DC SERIES BOILERS / WATER HEATERS

DC 15-95, DC 15-96, DC 20-125, DC 33-160

SEQUENCE OF OPERATION

The boiler / water heater will operate in a similar way for both a space heating

and a domestic hot water call for heat. When the boiler / water heater is powered

up the controller enters a self diagnostic mode and displays 2 in the Service

Display.
The Sequence of Operation is as follows:

The boiler / water heater receives a call for heat from closing terminals X4.6

and X4.7 (24 volts). The boiler / water heater can also receive a call from

Domestic Hot Water heating from the internal flow sensor, or from a 10KΩ

sensor or aquastat (X4.9 and X4.10 in 24V terminal).

The boiler / water heater does a safety check and energizes the fan for a pre-

purge (Service Display = 3)

Once the 5 second pre-purge is compete, the boiler / water heater enters a 5

second trial for ignition (Service Display = 4). If the boiler / water heater fails

to ignite, the boiler / water heater will compete a 5 second inter-purge then

another 5 second trial for ignition. This is repeated 4 times before a hard lock

out occurs. The Reset button

must be pressed to reset the controller

and allow for another attempt.

Once the burner is lit and flame has been proven the boiler / water heater

operates as it is programmed (Service Display = 5 for Space Heating or 6 for

Domestic Hot Water)

If the boiler / water heater reaches its target temperature and there is still a

call for heat or hot water. (Service Display = 1)

After the call for heat is satisfied, the boiler / water heater pump will operate

for an adjustable amount of time (Service Display = 0)

If the burner is on to maintain the heat exchanger temperature for DHW

Comfort mode or for Freeze Protection mode (Service Display = 7)

If the burner is on for Frost Protection (Service Display = 9)

MAIN

DISPLAY

SERVICE

DISPLAY

DESCRIPTION

[Pressure

e.g., 14 P]

The boiler / water heater is OFF. Press the On/Off

button to turn on the boiler

(blank)

No Call for Heat - Standby

XXX

Boiler / water heater pump running – pump post purge

XXX

Boiler / water heater water temperature reached target –

boiler / water heater pump is energized, call for heat still

present

XXX

Self-test – When power is applied to the boiler / water

heater the controller enters a self diagnostic mode for 5

seconds

XXX

Fan Pre-purge , Inter-purge and Post-purge

XXX

Trial for Ignition and Flame Proving

XXX

Heating – Space Heating

XXX

Heating – DHW

XXX

Burner on for Comfort mode or Freeze Protection mode

Table 9: Operating Display and Service Display Codes.

2.7

NOTE

The boiler / water heater

is equipped with a Frost

Protection feature. This

feature will operate the boiler

pump and the burner to help

protect the boiler / water

heater from freezing. If the

boiler / water heater is in

a hard lock-out condition

the burner will not operate,

however the boiler / water

heater pump will operate.

IBC is not responsible for

damages to the boiler, and/

or related components,

nor property damages that

may result from freezing

conditions.

Содержание DC 15-95



















































































Результаты поиска

Содержание DC 15-95

Отзывы:

Похожие инструкции для DC 15-95

Бренды по названию

Популярные бренды

IBC DC 15-95, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DC 15-95

Отзывы:

Похожие инструкции для DC 15-95

Бренды по названию

Популярные бренды