Ibanez troubadour T80N, Руководство пользователя

Страница: 9 / 54

7
EN
G
LI
SH
Names and Function on Each Part
1. POWER LED: This LED will light when amp power is activated by
the power switch.
2. INPUT LEVEL: Switches the signal level from MIC INPUT, line
level or mic level.
3. PHANTOM ON/OFF: Switches the phantom power ON/OFF. The
phantom power can supply +15V for T80N / +48V for T150S to
your capacitor microphone that connects with MIC INPUT. When
you use this switch, turn down the VOLUME to 0.
4. INST. INPUT: 1/4” phone jack input.*
1
5. MIC INPUT: Balanced input terminal with XLR Jack. 1-GND,
2-HOT, 3-COLD.*
1
6. CLIP INDICATOR: When this LED is illuminated in red, the pre-
amp is clipping. It is better for clean sound to turn down the VOL -
UME.*
1
7. VOLUME: Controls the pre-amplifier level.*
1
8. 3 BAND EQ: Refer to the spec sheet at the end of this manual for
frequencies and levels.*
1
9. CHORUS: Controls the speed of the chorus effect. Turn this con-
trol to the right to increase the speed. This function will be off at “0”
position.*
1
10. REVERB: Controls the reverb level. This function will be off at “0”
position.*
1
11. NOTCH FILTER: This is a notch filter that reduces feedback. Turn
this control until feedback stops. This function will be off at “0” posi -
tion.*
2
12. MASTER: Controls the overall output level of the amplifier. This
does not adjust the level of the LINE OUT and AUX IN signal.
13. PHASE INVERT: Inverts the phase of the signal. This helps you
stop feedback.* 2
14. MUTE: Mutes the singal from MIC INPUT and INST. INPUT. When
muted the LED will light. This will not mute the LINEOUT and AUX
IN signal.
15. PHONES: 3.5mm stereo mini output jack for stereo headphones.
The sound is not reproduced through the built-in speaker when
headphones are in use. The LINEOUT signal will still produce out -
put.
Warning:
This phones output can produce lots of volume. Ensure that the
MASTER and AUX VOLUME has been turned down before begin -
ning to play using the headphones, and then slowly increase the
volume until it has reached the desired level. Note inserting or re-
moving headphones at high volume levels may result in damage to
the headphones and to the user’s hearing.
16. AUX IN: 3.5mm stereo mini jack. This jack is designed to be con-
nected to the headphone output of a portable CD or MP3 player, or
similar device. Use the volume control of your portable player along
with the volume control on the amp to adjust the desired volume.
17. AUX VOLUME: Controls the signal level of the AUX INPUT.
18. LINEOUT: Monaural 1/4” phone jack with a line level output. You
can connect to an external mixing console or similar equipment.
REVERB and CHORUS signal are output in stereo.
19. FOOTSWITCH INPUT: Footswitch (sold separately) can be con-
nected here. A : Channel 1 Chorus / Reverb, B : Channel 2 Chorus /
Reverb, C : Mute / Phase Invert / Notch Filter
20. AC INPUT: Connect the included AC power cable to this connec-
tor. Only use the voltage indicated on the panel.
21. POWER SWITCH: This switch turns the power on/off. When you
are not using the amp, please leave it turned off.
22. TILT UP BAR: The built-in tilt system allows for better monitoring.
23. SPEAKER STAND HOLE:
Φ
38mm speaker stand adaptor (Only
T150S)
*
1
: The function works in each channel independently.
*
2
: The function might not work perfectly in all situations.