iB ES-100, Инструкция по эксплуатации

Страница: 6 / 6

04
05
3.2 Feeding Procedures
The Juice Extractors work very fast. First of all cut the orange or the lemon in
two halves.
With one hand hold half of the fruit and press it down firmly against the crown
Nº09 or Nº10 placed at the motor shaft. The juice will flow to the jar Nº08 and
previously through the sieve Nº07 (Pic-01).
3.3 Cleaning
IMPORTANT
Never do cleaning with machine plugged in, always unplug machine before
cleaning. Before taking out the Crown be sure Motor is completely stopped.
All removable parts must be removed and washed.
Follow the below instructions for washing removable parts:
3.3.1 Unplug the machine.
3.3.2 Remove the Lid Nº01, the Crown Nº 09 or 10 and then the Juice Chamber
Nº 02 (Pic- 01)
3.3.3 Wash all removable parts with running water and neutral soap and dry
them.
3.3.4 To reinstall them, follow the above order inversely.
4. General Safety Practices
The following safety instructions are addressed to both the operator of the
machine as well as the person in charge of maintenance. The machine has to be
delivered only in perfect conditions of use by the Distributor to the user. The user shall
operate the machine only after being well acquainted with the safety procedures
described in the present manual. READ THIS MANUAL WITH ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
Some areas of the electric device have parts that are connected or have parts
connected to high voltage. These parts when touched may cause severe electrical
chocks or even be fatal.
Never touch switches such as buttons, turning keys and knobs with your hands
wearing wet clothes and/or wet shoes. By not following these instructions operator could
be exposed to severe electrical shocks or even to a fatal situation.
4.1.2 Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make
sure the Switch is easy to be reached when necessary. Before any kind of maintenance,
physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure
the floor is clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be sure
the command is the correct one. Check this manual for further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to be
given for each operation step. Every step of the operation shall be taken only if a sign
has been made and responded.
4.1.3 Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical chocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components
of the machine.
DO NOT modify original characteristics of the machine.
DO NOT remove, tear off or maculate any labels sticked on the machine. If any
labels has been removed or is no longer legible contact your nearest dealer for
replacement.
READ CAREFULLY AND WITH ATTENTION THE SAFETY OR OPERATION
INSTRUCTIONS LABELS DISPLAYED ON THE MACHINE, AS WELL AS THE
INSTRUCTION MANUAL AND THE TECHNICAL CHARACTERISTICS WRITTEN
INSIDE .
4.2 Safety Procedures and Notes Before Switching Machine ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to be familiar with the set and that you have well understood all
information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad insulation could
cause electrical chocks as well as electrical leak. Before use check conditions of all
wires and cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood.
Every function and operational procedure have to be very clear to the operator. Contact
your nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being
sure it is the correct one.