Modello - Modèle - Model
Modell - Modelo
CORAL 118 WINE COOLER
Fabbricante - Constructeur
Manufacturer - Hersteller
Fabricante
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
PAGE
14/44
N° DOC
10. ENERGY SAVING TIPS
• Install the appliance in a dry, well-ventilated room away from heat sources (radiator, cooking surface and so on) and in a position
out of direct sunlight.
•
Follow the installation instructions to ensure adequate ventilation. Insufficient ventilation to the back of the appliance causes an
increase in energy consumption and reduces cooling efficiency.
• The internal temperature of the appliance depends on the room temperature, how often the doors are opened and where the
appliance is placed. These factors have to be taken into account when setting the thermostat. Only open the doors when strictly
necessary.
• Let hot food and drink cool down before placing them in the appliance.
•
The positioning of the shelves in the fridge has no effect on energy efficiency.
•
The fridge compartment light system uses a LED light, which at the same time ensures more efficient lighting and reduced energy
consumption.
11. PUTTING INTO OPERATION
If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand for at least three hours
before being started to allow the lubricating oil to settle in the compressor.
Failure to do so can cause total destruction of the compressor refrigerating system.
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord.
The fuse (or circuit breaker) size should be 13 amperes.
If the appliance is going to be used in an area or if your city / country is prone to power surges / outages; it is suggested
that you use a power surge protector for all electrical devices / appliances you use. The surge protector that you select
must have a surge block high enough to protect the appliance it is connected to. If you have any questions regarding
the type and size of surge protector needed contact a licensed electrician in your area. Damages due to power surges
are not considered a manufacturer covered defect and will void your product warranty.
Check that the voltage on the identification plate is the same as that of the network.
THE ELECTRICAL SUPPLY LINE TO WHICH THE REFRIGERATOR WILL
HAVE TO BE CONNECTED IS TO BE PROTECTED BY A VERY SENSITIVE
DIFFERENTIAL SWITCH (Rc=16A,Dc=30mA); IT IS ALSO TO BE
LINKED TO THE GENERAL EARTHING PLANT.
Earthing is necessary and compulsory by law.
Absolutely never use reduction units, patch cords, adapters or multiple socket
outlets to connect the counter. DIRECTLY connect the equipment to the mains.
The cable should be fully extended and located where it is unilikely to be struck, caught or stepped on, away from water
and the other liquids and heat sources and must not be damaged. In case of breakage of the power cable of the cabinet,
it must be replaced by the manufacturer or by instruction it change of it.
Follow the manufacturer’s instructions to install the unit, using qualified personnel and complying with the electrical
regulations for the specific country.
Incorrect installation may cause injury and damage; the manufacturer is not liable for this.
The manufacturer disclaims all responsability for any damage to people or things due to incorrect
observance of this rule.
12. OUTER CLEANING
WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
For a good preservation of the cabinet’s body a periodical cleaning is necessary.
1.
EXTERNAL BODY:
When necessary, the external body should be cleaned with a cloth and a neutral soap and water solution.
2. STAINLESS STEEL SURFACES:
Wash with warm water and mild detergent, rinse well and dry with soft cloth. Avoid scouring
pads etc. which will spoil the finish of the stainless steel.
3. SURFACES IN PLASTIC MATERIAL:
Wash with warm water and mild detergent, rinse well and dry with soft cloth; under
no circumstances should alcohol, methylated spirits or solvents be used.
4. GLASS SURFACES:
Only use products specifically designed for glass cleaning; It is not advisable to use ordinary water which
can leave a film of calcium on the surface of the glass.
WARNING!
Do not use jet of water to clean the cabinet: electrical wiring could be damaged.
WARNING!
Never use mechanical devices or any other means to accelerate the defrosting process,
other than those recommended by the manufacturer.