IAG IAG-ENG-7251 Скачать руководство пользователя

Страница: 1 / 49

IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI

Part# IAG-ENG-7251

Tools Required:

Ratchet, torque wrench, extensions,

needle nose pliers, hose cutter, snips/scissors, flat head

screw driver, hose clamping pliers

Sockets: 10mm, 12mm, ¼” allen,

Wrenches: ⅞”, 8mm, 10mm, 19mm 3mm allen, 5mm allen,

pry bar,

Other: Electrical Tape

Congratulations on the purchase of your Air/Oil Separator

(AOS) and thank you for choosing IAG Performance. This

installation manual is intended to guide you through the

removal of the factory PCV system and the installation of

the IAG AOS. If you already have an aftermarket catch can

or AOS installed, please consult the specific instructions for

your hardware to aid in its removal.

Note: The 2015+ STI cars are equipped with a “noise

symposer” engine sound enhancing device that connects

the intake to the firewall. These instructions do not cover

the removal process of this device. Usually this device is

already bypassed by the time an AOS is required.

Parts List

Part Name

Quantity

Notes

Air/Oil Separator

Oil Drain Hose Assembly

26” Hose Length

Top Coolant Hose Assembly

20” Hose Length, ½” I.D., -8ORB

Bottom Coolant Hose Assembly

20” Hose Length, ½” I.D., -8ORB

Discharge Hose

58” Hose Length, 1” ID

Block Breather Hose

25” Hose Length,

” ID

Valve Cover Breather Hose

74” Hose Length, ½” ID

Block Drain Replacement Hose

2” Hose Length, ¾” I.D.

Mounting Bracket

90° 5/8” Plastic Fitting

Block Breather Fitting

PCV Replacement Fitting

“Y” Fitting

Comp Series Upper Breather Fitting

Preinstalled

Fasteners for Breather Top Fitting

M4x8mm / preinstalled

AOS Drain Fitting

Preinstalled

Spring Clamps

Coolant Hose Spring Clamps

6x10mm Bolt

Mounting Bracket Hardware

½” High Temp Rubber Cap

” High Temp Rubber Cap

8” Zip Tie

11” Zip Tie

Содержание IAG-ENG-7251


















































Результаты поиска

Содержание IAG-ENG-7251

Отзывы:

Похожие инструкции для IAG-ENG-7251

Бренды по названию

Популярные бренды

IAG IAG-ENG-7251, Руководство по установке

Результаты поиска

Содержание IAG-ENG-7251

Отзывы:

Похожие инструкции для IAG-ENG-7251

Бренды по названию

Популярные бренды