IAG IAG-ENG-7251 страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 49

background image

IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com

34

40. Slide the relocation bracket (square hole side) into the

harness until it clips into place.

41. Next install the harness relocation bracket into the

same location (power steering line bracket) using the same

10mm bolt. Do not completely tighten the bolt yet. Adjust

the position of the main harness for clearance and fitment.

Then finish tightening the 10mm bolt. Finally press down

on the harness and slightly bend the bracket downwards

as shown.

«
...
32
33
34
35
36
...
»

Содержание IAG-ENG-7251


















































Отзывы:

Нет отзывов

Похожие инструкции для IAG-ENG-7251

Бренд: Samson Страницы: 7

PROVANTAGE 4500

Бренд: Warn Страницы: 18

Бренд: Fass Страницы: 28

Бренд: Hozelock Страницы: 40

Бренд: Dometic Страницы: 52

Ultra-Tow 52806

Бренд: Ultra-tow Страницы: 14

Бренд: Ultra Reef Страницы: 12

Бренд: S&B Filters Страницы: 12

Бренд: Roland Страницы: 204

Бренд: GE Multilin Страницы: 254

Бренд: Aqua One Страницы: 2

Бренд: Trixie Страницы: 20

Бренд: Aqua One Страницы: 12

Бренд: D'Addario Страницы: 15

Бренд: Chamberlain Страницы: 12

Бренд: YOKOGAWA Страницы: 178

Бренд: Unika Страницы: 12

Бренд: iGenix Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды