INSTALLATION
1. Refer to Fig. 1, loosen the Screw A on the bottom box by about 5 turns counter-clockwise
2. Refer to Fig. 2 & Fig. 3, detach the bottom box of the smoke detector.
3. Refer to Fig. 3, open the cover of the battery compartment, connect supplied 9V battery and then close the cover.
4. Re-assemble the bottom box with the main body. The marks should be at the position shown in Fig. 5 after
combination. And then tighten the Screw A.
5.
Keep pressing the Clear/Enroll Button on
i4H-
LS-20 for over 3 seconds and then release it, the
i4H-
LS-20 would
keep beeping and all LEDs blink. This means the system is ready for enrolling device.
6. Within 30 seconds press the TEST button of the
i4H-
SM-3S for 2 seconds. If you hear 3 short beeps from the
i4H-
LS-20
soon later then enrolling successes, otherwise you will hear one long beep after 30 seconds that means enrolling fails,
you
have to repeat enrolling action.
Note: Avoid activating any other sensors during the 30 seconds Device Enroll period.
Remarks: In case you have to change the device‟s attribute, please do it on the cloud web directly, or refer to
HyperSecureLink software user guide to change it by computer.
7. Locate the smoke detector properly, and fixed the bracket with the two supplied screws on the ceiling. And then mount
the smoke detector on the bracket.
Note: Keep the smoke detector within effective radio range away from the base unit.
8. Press the “
TEST
” button, and check if the base unit is activated.
Note:
1) The LED starts flashing after a few seconds when smoke is detected, then the internal buzzer sounds
and activates the base unit it after 10 seconds.
2) The LED flashes every
43
seconds to indicate the detector is in standby mode, and it beepsperiodically
if 9V battery goes too low. Replace the battery when these beeps occur.
3) Maintenance at least once a year is essential. Open the cover then clean the sensing chamber with
vacuum cleaner carefully.
4) SM-3S comes with cover latches that prevent the cover from closing if no battery is installed.
PREFERRED LOCATION
LOCATIONS TO BE AVOIDED
Do NOT locate detector in:
The Kitchen: Smoke from cooking might cause an unwanted alarm.
Near Ventilating fan, Fluorescent lamp or Air-Conditioning equipment: Air drafts from them may affect the sensitivity
of the detector.
Near Ceiling beams or over Cabinet: Stagnant air in this area may affect the sensitivity of the detector.
In the peak of an 'A' frame type of ceiling.
SPECIFICATIONS:
Detection:
Photo-electric Chamber
Thermistor for heat, alarm level:
above
57+/- 3
℃
(Only for
i4H-
SM-3SH)
Either of smoke or heat alarm would trigger the detector
Power:
9V Battery
Supervision:
Sends heartbeat signal at 60-minute intervals. When Tamper or
Low -Battery condition is detected, it reports automatically.
Current Consumption:
10uA@ standby, 16mA@ activation
Battery Life:
About 1~1.5 years
Working Temperature:
0
℃
~ 50
℃
Ambient Relative Humidity:
10%
～
85%
Alarm Sound Level:
85dB@3m
Indicator Light:
LED flashes every 32 seconds approximately.
Low Battery:
Beep every 32 seconds approximately.
Actuation Indicator:
LED ON, Buzzer ON
Size:
φ101mm x H 52mm
Weight:
About 126g (w/o battery)
BATH
ROOM
LIVING ROOM
BED
ROOM
BED
ROOM
STORE
ROOM
DINNER
ROOM
In the center of the ceiling
At the top
of a stairway
0.6m
At least 0.6m
from the wall
1.2 m
In the ceiling of
the corridor is
less than 1.2 m
in width
