QUICK START GUIDE
Di210 / Di210B Indoor Dome
Adjust the Camera Position
The dome camera has three axes for positioning the camera. While
monitoring the picture on the monitor, adjust the camera position as
follows:
Horizontal Adjustment
Rotate the 3D gimbal in the base. Do not turn the gimbal more than
360º or this may cause the internal cables to twist and break.
Vertical Adjustment
After loosening the thumb nuts, position the camera as desired and
then finger-tighten the thumb nuts to set into place.
Horizontal Rotation for Wall Mount and Tilted Ceilings
Rotate the lens base (maximum 360º) until you are satisfied with the
scope of view.
Figure 3-4
Camera Adjustment
5
1
2
3
4
3-4 Illustration
1. Tilt adjustment bracket and thumb nuts (x2) for
vertical adjustment
2. Axis ring for horizontal and tilted rotation
3. Zoom lever
4. Focus lever
5. Rotate 3D gimbal in base for horizontal
adjustment
Adjusting the Lens
1.Slightly loosen the zoom lever (#3) counter-
clockwise and adjust the zoom lever to determine
the image view.
2.Slightly loosen the focus lever (#4) counter-
clockwise and adjust the focus for optimal picture
sharpness.
3.Re-tighten the zoom lever and focus lever after
adjustment.
Note: It is important that you lock the zoom and
focus levers after making adjustments to avoid
an unfocused view caused by the surrounding
environment (movement, vibration, temperature
change, etc.).
Optional Camera Settings
See Figure 3-5 for Camera Adjustment Functions located
on the camera board.
Figure 3-5
Camera Adjustment Functions
1
2
3-5 Illustration
1. Monitor out
2. OSD control switch
OSD Control Switch
Use the UP/DOWN/LEFT/RIGHT
functions of the OSD switch and the
ENTER key to control the OSD menu.
Camera
Signal system
NTSC
Scanning system
2:1 Interlace
Sync system
Internal / Line Lock
Scanning frequency (H)
15.734KHz
Scanning Frequency (V)
59.94Hz,
Day & Night mode
Auto / Color / BW (electronic D/N) / EXT
Imaging area
4.9 mm x 3.7 mm
Image sensor
1/3” SONY CCD
Horizontal resolution
600 TVLines
Effective pixels (HxV)
768x494
Built-in lens
F1.2, f=2.8~10.5mm
Min. illumination
0.015 lux(F1.2, AGC on, 10 IRE) ; 0.2 lux(F1.2,
AGC on, 50 IRE)
BLC
BLC / HSBLC / OFF
OSD
Built in
White balance
ATW / AWB / INDOOR / OUTDOOR / MANUAL
/ AWC
Electronic Shutter
1/60 / x2 / x4 /...../ FLK (selectable)
D-WDR
OFF / INDOOR / OUTDOOR
3DNR
ON(Level: 0~100 adjustable) / OFF
S/N ratio
More than 50dB (AGC off)
Sense up Level
Auto(6 levels selectable) / OFF
View angle
Wide= 99.5°(H), 73.2°(V) ; Tele= 27.4°(H),
20.6°(V)
Video output
1Vpp composite output 75 ohm
Gamma correction
0.05~1.0 selectable(default 0.45)
Motion Detection
4 areas
Privacy Mask
8 masks
D-ZOOM
ON / OFF
Mirror
Off / Mirror / V-Flip / Rotate
Monitor Out
Yes
Power supply
Power requirement
DC12V / AC24V
Environment
Operating temperature
-10ºC ~ 50ºC (14 ºF ~ 122 ºF)
Operating humidity
90% RH
Storage temperature
-20ºC ~ 60ºC (-4 ºF ~ 140 ºF)
Mechanism
Dimensions (D X H)
112mm X 100.8 mm (4.41" x 3.97")
Weight(g)
300g approx.
Ordering information
C-Di210/ C-Di210B
i³ INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
Canada 780 Birchmount Road,
Unit 16, Scarborough,
ON, M1K 5H4
U.S.A. 440 Lawrence Bell Drive,
Suite 16, Williamsville
NY, 14221
