Hyundai HYT150 Скачать руководство пользователя страница 42

Страница: 42 / 52

Maintenance

www.hyundaipowerproducts.co.uk

01646 687 880

[email protected]

NOTE -

Where necessary, all corrective actions should be carried out by suitably qualified

person.

CAUTION!

For your own safety, turn the tiller off before any maintenance.

Problem

Possible Cause

Possible Solution

Engine cannot be
started

1. Not enough fuel
2. Fuel valve is OFF
3. Engine switch is OFF
4. Carburettor is blocked
5. No spark from the spark plug

1. Check fuel level in fuel tank
2. Open the fuel valve
3. Turn the engine switch ON
4. Loosen the drain knob with the
fuel valve ON. Fuel can flow out
freely and then re-tighten drain
knob
5. Remove and clean the spark
plug

Clutch not working

1. Engine speed is low
2. Belt too long
3. Spring failure
4. Bearing inside gearbox
failure

1. Open throttle, increase engine
speed
2. Replace
3. Replace
4. Replace

Sliding

1. Spring/belt failure

1. Replace

Abnormal noise from
gears

1. Loose bearing
2. Drive shaft deformed
3. Gears wear out

1. Replace
2. Replace
3. Replace

Oil leakage

1. O type sealing failure
2. Loose bolts

1. Replace
2. Tighten

If the engine still cannot be started, take your machine to an authorized dealer.

Troubleshooting

Содержание HYT150





















































Результаты поиска

Содержание HYT150

Отзывы:

Бренды по названию

Популярные бренды

Hyundai HYT150, Инструкция по эксплуатации

Результаты поиска

Содержание HYT150

Отзывы:

Бренды по названию

Популярные бренды