background image

 

 

 

 

 

9.

 

DISPOSAL & RECYLING.

 

 

9.1

 

Do not dispose of electric equipment together with household waste material! In observance 

of European Directive 2012/19/EC on waste electrical and electronic equipment and its 
implementation in accordance with national law, electric equipment that have reached the end of 
their life must be collected separately and returned to an environmentally compatible recycling 
facility. If electrical appliances are disposed of in landfills or dumps hazardous substances can leak 
into the groundwater and get into the food chain, damaging your health and well-being. 
19.2  For further information on the disposal of this product, please contact your dealer or your 
nearest domestic waste collection service. 

 

9.3

 

Reduce – Reuse - Recycle unwanted materials instead of disposing of them as 

waste. All tools, accessories and packaging should be sorted, taken to a recycling 
centre and disposed of in a manner which is compatible with the environment. 

 

9.4

 

When the product is no longer required, it must be disposed of in a manner 

which is compatible with the environment. 

 

10.

 

TROUBLESHOOTING.

 

 

Problems

 

Reasons

 

Solutions

 

Compressor does not run.

 

1.

 

Voltage cuts off. 

 

2.

 

The main voltage is too low. 

 
 

3.

 

External temperature is too low. 

4.

 

Motor overheats.

 

1.

 

Check cable, plug, fuse and 

outlet. 
2.

 

Avoid the long extension 

cords. Use the cable with the 
sufficient wire cross section. 
3.

 

Not operate below 5 

℃ 

4.

 

Cooling down the motor 

may eliminate the failure.

 

Compressor runs but has 
no pressure.

 

1.

 

The valve (18) leaks 

2.

 

The seal is broken. 

 

3.

 

The condensation drain plug 

(4) has become loose.

 

1.

 

Replace check valve. 

2.

 

Get broken seal 

replaced by a specialist. 
3.

 

Tighten the screw by hands. 

Check the seals on the screw 
and replace it if necessary.

 

Compressor is running, 
pressure is displayed on 
the gauge, but tools do 
not run.

 

1.

 

Hose connections leak. 

 

 

2.

 

Quick release coupling leak. 

 
 

3.

 

The pressure is set too low

 

1.

 

Check the compressed air 

hose and tool, replace them if 
necessary. 
2.

 

Check the quick release 

connections 
and replace them if necessary. 
3.

 

Increase the pressure 

regulator adjustment knob. 
Check for hose leak between 
regulator and tool.

 

Page 14

Rev 2

Содержание HY2524

















Отзывы: