manualshive.com logo in svg

Hyundai DHY6000SE, Руководство по обслуживанию

Поделиться
Скачать
Hyundai DHY6000SE Скачать руководство пользователя страница 12

2. Periodic Maintenance

2.1   Service Intervals      

Good maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air 

pollution.

 

 

 

Exhaust gas contains poisonous carbon monoxide. Shut off the engine before  

 

 

 

perform any maintenance. If the engine must be run, make sure the area is well  

   ventilated.

Periodic maintenance and adjustment is necessary to keep the generator in good operating condition. 

Perform the service and inspection at the intervals shown in the Maintenance schedule below:

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

Changzhou ITC Power Equipment Manufacturing Co.,Ltd.

WARNING

(1) Service more frequently when used in dusty areas.

(2) These items should be serviced by an authorized generator dealer.

(3) When more often use, only servicing according to above correct intervals can insure the generator set 

     long-term use.

9

POWER PRODUCTS 

Содержание DHY6000SE


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды