Hyster H177 Скачать руководство пользователя

Страница: 49 / 80

8000 SRM 707

Maintenance Procedures Every 1000 Hours or 6 Months

CAPSCREW

WASHER

FUEL FILTER
HEAD

TOP SEAL

O-RING

FUEL FILTER
ELEMENT

BOTTOM SEAL

FUEL FILTER
BOTTOM

Figure 30. Diesel Fuel Filter

Figure 31. Water Separator

Legend for Figure 31

CAPSCREW

WASHER

FUEL FILTER
HEAD

TOP SEAL

FUEL FILTER

BOTTOM SEAL

FUEL FILTER
HOUSING

WATER SENSOR
LEAD

PLUG

Water Separator, Remove Water

WARNING

The water separator is full of diesel fuel and
water and can be a fire hazard when being
drained. Place a container under the fuel fil-
ter to catch the water and fuel being drained
from the water separator.

Remove plug from bottom of water separator. See
Figure 31.

Drain water from water separator until there is
only fuel flowing from water separator.

Install plug into water separator.

Water Separator, Replace

WARNING

While holding bottom of water separator bowl,
remove capscrew at top of water separator as-
sembly. See Figure 32.

Remove water separator bowl from water sepa-
rator head and remove filter from bowl. Discard
both seals.

Empty fuel and water from water separator bowl
into an approved container for disposal.

Install new seals and filter element into water
separator bowl.

Install water separator bowl assembly onto wa-
ter separator filter head.

Содержание H177

















































































Результаты поиска

Содержание H177

Отзывы:

Похожие инструкции для H177

Бренды по названию

Популярные бренды

Hyster H177, Периодическое техническое обслуживание

Результаты поиска

Содержание H177

Отзывы:

Похожие инструкции для H177

Бренды по названию

Популярные бренды