background image

P1.6 Lift Speed

This parameter allows the user to adjust the mast
lift  speed  from  the  maximum  lift  speed  to  some
lower  speed  within  the  parameter  range.  The  set-
ting range is from 1 to 9. Setting this parameter to
“9”  will  result  in  maximum  lift  speed.  Setting  this
parameter to “1” will result in minimum lift speed.

P1.7 Lower Speed

This parameter allows the user to adjust the mast
lower  speed  from  the  maximum  lower  speed  to
some lower speed within the parameter range. The
setting range is from 1 to 9. Setting this parameter
to “9” will result in maximum lower speed. Setting
this parameter to “1” will result in minimum lower
speed.

P1.8 Lift Accel

This  parameter  allows  the  user  to  adjust  the  hy-

draulic pump motor acceleration during lifting from
the maximum acceleration rate to some lower accel-
eration  rate  within  the  parameter  range.  The  set-
ting range is from 1 to 9. Setting this parameter to
“9” will result in maximum acceleration during lift-
ing. Setting this parameter to “1” will result in min-
imum acceleration during lifting.

P1.9 Lift Decel

This  parameter  allows  the  user  to  adjust  the  hy-
draulic  pump  motor  deceleration  during  lifting
from the maximum deceleration rate to some lower
deceleration  rate  within  the parameter range. The
setting range is from 1 to 9. Setting this parameter
to  “9”  will  result  in  maximum  deceleration  during
lifting.  Setting  this  parameter  to  “1”  will  result  in
minimum deceleration during lifting.

P1.10 Lower Accel

This  parameter  allows  the  user  to  adjust  solenoid
acceleration while lowering from the maximum ac-
celeration  rate  to  some  lower  acceleration  rate
within  the  parameter  range.  The  setting  range  is
from 1 to 9. Setting this parameter to “9” will result
in  maximum  acceleration  during  lowering.  Setting
this parameter to “1” will result in minimum accel-
eration during lowering.

P1.11 Lower Decel

This  parameter  allows  the  user  to  adjust  solenoid
deceleration while lowering from the maximum de-
celeration  rate  to  some  lower  deceleration  rate
within  the  parameter  range.  The  setting  range  is
from 1 to 9. Setting this parameter to “9” will result
in  maximum  deceleration  during  lowering.  Setting
this parameter to “1” will result in minimum decel-
eration during lowering.

P1.12 Tilt Speed Main

This  parameter  is  used  to  adjust  tilt  speed  when
the mast is elevated above free lift. It also controls
tilt  speed  when  the  mast  is  below  free  lift  if  the
truck  is  NOT  equipped  with  "Reduced  Speed  Tilt"
option.

P1.13 Tilt Speed Free

This parameter allows the user to adjust the maxi-

mum tilt speed when the mast is raised above free-
lift  position.  The  setting  range  is  from  1  to  9.  Set-
ting  this  parameter  to  “9”  will  result  in  maximum
tilt speed. Setting this parameter to “1” will result
in minimum tilt speed.

P1.14 Tilt Accel

This parameter allows the user to adjust the rate of
tilt speed acceleration. The setting range is from 1
to  9.  Setting  this  parameter  to  “9”  will  result  in
maximum  accel  speed.  Setting  this  parameter  to
“1” will result in minimum accel speed.

P1.15 Tilt Decel

This parameter allows the user to adjust the rate of
tilt speed deceleration. The setting range is from 1
to  9.  Setting  this  parameter  to  “9”  will  result  in
maximum  decel  speed.  Setting  this  parameter  to
“1” will result in minimum decel speed.

P1.16 Sideshift Speed Main

This parameter allows the user to adjust the maxi-
mum sideshift speed. The setting range is from 1 to
9. Setting this parameter to “9” will result in maxi-
mum sideshift speed. Setting this parameter to “1”
will result in minimum sideshift speed.

2200 SRM 2023

Supervisor-Level Menu

9

Содержание C219






















Отзывы: