HySecurity Nice 7251 Slide страница 31 Скачать руководство пользователя

Страница: 31 / 82

7251 / 7351 Slide Gate Operator

INSTALLATION AND PROGRAMMING MANUAL

www.hysecurity.com • 800-321-9947

After performing all necessary power connections per the instructions, the control board will power
up as follows:

1. The display will show:

a) the company name, followed by...

b) the ﬁrmware version, then...

c) “Scanning BlueBUS” as the control board is scanning for compliant safety devices.

2. If safety devices (such as photo eyes) are found and determined to be functional, then display

defaults the current gate status (Open or Close) indicating the board is ready to “Learn” the
gate limits and you may proceed to INSTRUCTION 16.

3. If no safety devices are attached or functioning, display will show “BlueBUS Error”.

4. If using the BlueBUS photo eyes when error is displayed, check for BlueBUS wiring errors

and/or observe diagnostic LEDs per INSTRUCTION 18 to determine problem. If using the

reflective photo eye with reflector, refer to the separate instructions included in the kit for

troubleshooting instructions.

5. To reset the board after a scanning error (BlueBUS Error), remove power from the board

(unplug battery, Main DC Input, and solar connector) then after a few seconds reapply power
(plug power connectors back in).

6. Board will display “Scanning BlueBUS” while it scans for monitored safety devices.

7. If safety devices (such as photo eyes) are found and determined to be functional, then display

defaults to the current gate status (Open or Close) indicating the board is ready to ‘learn” the
gate limits, and you may proceed to INSTRUCTION 16.

8. If safety devices provided in the kit are determined to be defective, contact Nice technical

support.

POWER UP CONTROL BOARD

Содержание Nice 7251 Slide



















































































Результаты поиска

Содержание Nice 7251 Slide

Отзывы:

Похожие инструкции для Nice 7251 Slide

Бренды по названию

Популярные бренды

HySecurity Nice 7251 Slide, Инструкция по установке и программированию

Результаты поиска

Содержание Nice 7251 Slide

Отзывы:

Похожие инструкции для Nice 7251 Slide

Бренды по названию

Популярные бренды