manualshive.com logo in svg

Hypertherm Powermax 30, Руководство по обслуживанию

Поделиться
Скачать
Hypertherm Powermax 30 Скачать руководство пользователя страница 12

Hypertherm 

Plasma Systems

1-1

8-06

Section 1

SAFETY

In this section:

Recognize safety information ...................................................................................................................................1-2

Follow safety instructions..........................................................................................................................................1-2

Cutting can cause fire or explosion...........................................................................................................................1-2

Electric shock can kill................................................................................................................................................1-3

Static electricity can damage circuit boards..............................................................................................................1-3

Toxic fumes can cause injury or death......................................................................................................................1-4

A plasma arc can cause injury and burns .................................................................................................................1-5

Arc rays can burn eyes and skin...............................................................................................................................1-5

Grounding safety ......................................................................................................................................................1-5

Compressed gas equipment safety ..........................................................................................................................1-6

Gas cylinders can explode if damaged .....................................................................................................................1-6

Noise can damage hearing .......................................................................................................................................1-6

Pacemaker and hearing aid operation ......................................................................................................................1-6

A plasma arc can damage frozen pipes....................................................................................................................1-6

Additional safety information.....................................................................................................................................1-6

Warning labels ..........................................................................................................................................................1-7

Содержание Powermax 30

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды