Hypertherm PAC500 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 96

background image

SAFETY

1-2

Hypertherm

Plasma Systems

11-98

SAFETY

RECOGNIZE SAFETY INFORMATION

The symbols shown in this section are used to

identify potential hazards. When you see a safety
symbol in this manual or on your machine, understand
the potential for personal injury, and follow the related
instructions to avoid the hazard.

FOLLOW SAFETY INSTRUCTIONS

Read carefully all safety messages in this manual and
safety labels on your machine.

• Keep the safety labels on your machine in good

condition. Replace missing or damaged labels
immediately.

• Learn how to operate the machine and how to use

the controls properly. Do not let anyone operate it
without instruction.

• Keep your machine in proper working condition.

Unauthorized modifications to the machine may
affect safety and machine service life.

DANGER

WARNING

CAUTION

A signal word DANGER or WARNING is used with a
safety symbol. DANGER identifies the most serious
hazards.

• DANGER and WARNING safety labels are located

on your machine near specific hazards.

• WARNING safety messages precede related

instructions in this manual that may result in injury
or death if not followed correctly.

• CAUTION safety messages precede related

instructions in this manual that may result in
damage to equipment if not followed correctly.

Fire Prevention
• Be sure the area is safe before doing any cutting.

Keep a fire extinguisher nearby.

• Remove all flammables within 35 feet (10 m) of the

cutting area.

• Quench hot metal or allow it to cool before handling

or before letting it touch combustible materials.

• Never cut containers with potentially flammable

materials inside – they must be emptied and
properly cleaned first.

• Ventilate potentially flammable atmospheres before

cutting.

• When cutting with oxygen as the plasma gas, an

exhaust ventilation system is required.

Explosion Prevention
• Do not use the plasma system if explosive dust or

vapors may be present.

• Do not cut pressurized cylinders, pipes, or any

closed container.

• Do not cut containers that have held combustible

materials.

CUTTING CAN CAUSE FIRE OR EXPLOSION

WARNING

Explosion Hazard

Argon-Hydrogen and Methane

Hydrogen and methane are flammable gases that
present an explosion hazard. Keep flames away from
cylinders and hoses that contain methane or hydrogen
mixtures. Keep flames and sparks away from the torch
when using methane or argon-hydrogen plasma.

WARNING

Hydrogen Detonation with Aluminum Cutting

• When cutting aluminum underwater, or with the

water touching the underside of the aluminum, free
hydrogen gas may collect under the workpiece and
detonate during plasma cutting operations.

• Install an aeration manifold on the floor of the water

table to eliminate the possibility of hydrogen
detonation. Refer to the Appendix section of this
manual for aeration manifold details.

«
...
8
9
10
11
12
...
»

Содержание PAC500

































































































Отзывы:

Нет отзывов

Похожие инструкции для PAC500

Бренд: MAC TOOLS Страницы: 30

Бренд: MAHA Страницы: 23

Бренд: Qtx Страницы: 5

Pack TYXAL+ Access

Бренд: DELTA DORE Страницы: 11

Digital Movie DM 90.2

Бренд: Canton Страницы: 74

Бренд: Cal-Royal Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: OMCN Страницы: 40

Бренд: 4CR Страницы: 7

Бренд: Omega Страницы: 16

Бренд: Daewoo Страницы: 35

Бренд: Jensen Страницы: 2

Бренд: Acesonic Страницы: 22

Бренд: Euroscreen Страницы: 39

Бренд: GPX Страницы: 12

SONIC STARLIGHT

Бренд: Hama Страницы: 20

RAZOR CUT 45 PFC

Бренд: Xcel-Arc Страницы: 24

Бренд: Tuxedo Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды