Hypertherm Echion Скачать руководство пользователя страница 170

Страница: 170 / 194

Installation

170

810770 Operator

Manual

Echion

Inst

alla

Intensifier Control

Intensifier On

This enables and disables the intensifier.

When intensifier control is off:

• the

Intensifier On

box is gray.

• the primary screen shows a red × on the intensifier symbol.

Percent

Overstroke percent is the increased stroke rate that is permitted before an overstroke
fault condition occurs. The maximum intensifier stroke rate is calculated using the
motor wattage and the size of the hydraulic pump. Refer to

Stroke rate

on page 141.

The rate can be adjusted to compensate for variations in plumbing configurations and
flow rates.

Touch this field to open a numeric keypad.

Use the keypad to enter the maximum overstroke percentage permitted
before a fault occurs.

The default is 5%. The maximum is 20%.

Touch

Enter

Total Hours

This shows the total hours that the intensifier has been in operation.

Strokes

This shows the total number of strokes on the intensifier.

A stroke is counted each time a proximity switch is activated.

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды