background image

 
ERROR MESSAGES 

INPUT VOLTAGE ERROR 

Input voltage is below 11.0V or exceeds 15.0V 

NO BATTERY 

Battery not detected 

OUTPUT BATT REVERSE POLARITY 

Battery is connected in reverse polarity to Output leads 

OUTPUT CIRCUIT PROBLEM 

Non-Specific Circuit error. Check battery condition 

CHECK BATT OPEN CIRCUIT 

Battery disconnected during charging 

CHECK BATT OVER VOLTAGE 

Battery voltage too high to match charger settings 

CHECK BATT LOW VOLTAGE 

Battery voltage too low to match charger settings 

BALANCER VOLTAGE TOO HIGH 

If voltage per cell is too high during balancing, this message may appear.

 

BALANCER VOLTAGE TOO LOW 

If cell’s voltage falls too low during balancing, this message may appear 

DON’T CHARGE Lixx WITH THIS MODE 

A Lithium pack is connected by balancer, but NiCd/NiMH/Pb mode is selected for charging 

 
Note: If the incorrect number of cells is selected for a lithium type battery, and charging is begun, the charger may give error 
immediately and stop charging. In some cases, however, the charger will begin charging at the (lower) voltage it sees as 
correct, and watch all cells to confirm the incorrect setting. For example, if you connect a 3S pack but set the charger for 4S 
by mistake, the charger may begin by charging at 3S voltage level, and watch all cells. When the mistake is confirmed, the 
charger will give error and terminate. This is normal and correct behavior. 
 
 
 
 
WARRANTY 
 
HYPERION Chargers are guaranteed to be free from defects in materials and workmanship for a period of one calendar year 
from date of purchase.  Your selling dealer is your first point of contact for warranty issues.  Return postage costs are the 
responsibility of the user in all cases. Submit copy of original receipt with the return. 
 
Damage due physical shock (dropping on the floor, etc), inappropriate power supply (automotive battery charger, etc!), water, 
moisture, and humidity are specifically NOT covered by warranty. It is well to carefully check your charger before making a 
return, as problems in setup, cabling, or power supply are much more common than defects in the charger.   
 
 
 
 
Enjoy the Power! 
 
 
 
 
The Hyperion Team 

 

Содержание EOS0606i-B









Отзывы: