background image

Seite 10

Best.-Nr. / Item-No. / art. 028-1040

General Safety Instructions For Electric Models

 This model is not a toy. Allowed for children over 14 years.

 Use the model accordingly to chapter 5 "How To Use" in this instruction manual.

 Assemble the model accordingly to this instruction manual. Do not alter or modify the model. Only use parts that are officially 

  recommended by KYOSHO Deutschland. 

 Always pay close attention to the manuals that are included to accessory parts.

 Do not fly the model before you have finished the assembly completely according to this manual.

 Before you fly, check all functions of the model carefully. Check if your frequency is clear and not used by any

  other pilots in your area. This may cause radio interference.

 Never fly your model near other human beings, animals or other obstacles. You are responsible for flying the model, so

  you have to check carefully your flight area.

 Stop flying immediately if you realize any radio interference. Check the system for the cuase and change the frequency

  if necessary.

 Do not touch any moving or hot motor parts during action! Let all components cool down before you handle them. 

 Check your model carefully after each flight. Replace parts if they are worn out or if they are defective.

 Keep your hands out of reach from rotating or hot parts of the model.

 Keep in mind that plastic parts easily break under cold temperature conditions. 

 If you are a novice in flying you should ask experienced pilots for assistance during your first flights.

 Protect yourself from dust and other small things when you test run your propeller drive on the ground.

 Keep all electronic components dry and clean!

 Take care that your motor does not get overload or gets blocked under full power.

 Let the motor cool down after restarting the model again.

 Charge your batteries carefully. Always watch the charging process and make sure all connectors are in good conditions.

 Do not shorten the battery by connecting the pluspole with the minuspole directly!

 Make sure that the wires do not touch rotating or hot parts of the model.

 CE-certification for electric motor: EN 50081-1, IEC 1000-4-2, IEC 1000-4-3, EN 50082-1

 In case of technical questions please contact our helpdesk by phone: +49-4191-932678 or by e-mail: [email protected]

5. Sicherheitshinweise / Safety Instructions / avviso di sicurezza

Содержание JODEL ROBIN DR-400





















Отзывы: