HydroTherm MultiPulse AM Series Скачать руководство пользователя страница 15

Страница: 15 / 48

CONDITION “E” continued …

POSSIBLE CAUSE

VERIFICATION

SOLUTION

Wiring to GC-4A (115V)

Turn Rocker Switch OFF. With an

If no continuity on any wire, replace

ohmmeter, check continuity of red &

or repair as required.

black wires of the 3-conductor Molex
connector.

If all continuity checks ok, check if
motor wire terminals mate correctly
when joined.

Turn gas valve top knob to “ON” after
completing checkout.

CONDITION #1 - BOILER IGNITES (8 SECONDS) THEN SHUTS OFF

GC-4A Light is “ON”, Red Light “ON”, Green Light “ON” (during 8 second ignition trial). After 3 min. 45 sec (5
unsuccessful igntion trials) the GC- 4A light then blinks.

IF THE BOILER, WHEN IT RUNS, STOPS BEFORE THE GREEN LIGHT GOES OUT - PROCEED TO
“CONDITION #3.”

POSSIBLE CAUSE

VERIFICATION

SOLUTION

Copper Pressure Sensing

Turn Rocker Switch OFF & remove

Repair or replace as necessary.

Tube

top from Air Cushion Chamber
(A.C.C.). (On AM-100 & -150 remove

Runs from Gas Cushion

fan assembly). Check tube for breaks

Chamber (G.C.C.) valve

at the GCC valve plate & on the

plate to Combustion

AM-300 at the fitting on the ACC

Prove-Pressure Switch (PS1).

wall. Check unions are tightly
connected.

Pressure Switch (PS1)

If removed, replace fan assembly

If boiler runs more than 9 seconds

(Combustion Prove Switch)

and air cushion chamber top and

(with jumper in place), replace switch

turn Rocker Switch ON.

(PS1).

Immediately after boiler starts, place

If boiler runs 8 seconds (stops when

jumper across PS1 pressure

Green Light goes OFF) with the

switch terminals (R-W). DO NOT

jumper in place, proceed with

PUT JUMPER ON UNTIL GAS

verification.

VALVE IS ENERGIZED.

CAUTION: TERMINAL VOLTAGE
EXCEEDS 300 VOLTS.
(Remove jumper after test).

Wiring - Purple Wires (2)

Check both purple wires from (PS1)

If loose, reconnect wires. Repeat

From PS1 to GC-4A Ignition

pressure switch to ignition control.

Pressure Switch verification. If boiler

Control

Connections must be secure to

runs less than 9 seconds (with

complete circuit from module.

jumper in place), switch is ok.

If no loose wires, replace GC-4A
ignition module following instructions
packaged with replacement.

Содержание MultiPulse AM Series

















































Результаты поиска

Содержание MultiPulse AM Series

Отзывы:

Похожие инструкции для MultiPulse AM Series

Бренды по названию

Популярные бренды

HydroTherm MultiPulse AM Series, Руководство по устранению неисправностей

Результаты поиска

Содержание MultiPulse AM Series

Отзывы:

Похожие инструкции для MultiPulse AM Series

Бренды по названию

Популярные бренды