HydroTherm MultiPulse AM Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

background image

13

CONDITION E

GC-4 LIGHT BLINKING

Turn the Rocker Switch OFF and ON. Observe GC-4 light and clock ON time before it begins to blink.

If Red or Amber Lights OFF, replace lamp or switch.

If the boiler starts and runs, a temporary problem may have corrected itself, (I.E., low gas pressure or a blockage
of the inlet, etc). However, there may also be a slow draining condensate or a partially blocked exhaust, see
Blocked Exhaust under “CONDITION #2B”. Stop and start the boiler a number of times to assure normal
operation has been restored.

If boiler does not ignite or ignition is rough - see “CONDITION 2.”

If GC-4A light is ON 3 min, 30 sec., then starts blinking and boiler attempted ignition - proceed to “CONDITION 2”.

If GC-4A light is ON 3 min, 30 sec., then starts blinking and if boiler “coughs” or does not attempt ignition, pro-
ceed to “CONDITION 2”.

If GC-4A light is ON 2 min, 45 sec., then begins to blink, measure fan pressure (see “PROCEDURES” section)
and use one of the two procedures below.

MODEL NO.

MINIMUM FAN PRESSURE (PS2)

AM-100/-150

+1.4" W.C.

AM-300

+0.8" W.C.

1.

If measured fan pressure exceeds the minimum for fan prove switch (PS2) operation.

POSSIBLE CAUSE

VERIFICATION

SOLUTION

Wiring

Turn Rocker Switch OFF. Remove

If no continuity, check wire and

the 6-pin Molex connector from the

connectors until continuity is

the GC-4A. (Keep Fan Switch (PS2)

obtained - reconnect Molex to GC-4A

jumper in place). With an Ohm-

and run Fan Prove Switch check.

meter check for continuity across
pin-4 (grey) and 5 (lt.blue).

If continuity but, condition above
exists-replace GC-4A.

Fan Prove Switch (PS2)

**Turn Rocker Switch OFF. Turn

If boiler starts, (PS2) pressure

(N.O.) contacts

Rocker Switch ON. Jumper pressure

switch is defective - replace it.

(Factory Fixed Setting)

switch (PS2) contacts.

If the GC-4A light begins to blink after
2 min. 45 sec., (PS2) switch is ok.
Proceed with check.

If the boiler attempts to start and the
GC-4A light blinks after 3 min.30 sec.,
(PS2) switch is defective - replace it.

** NOTE: Fan must be operating before placing jumper across swith PS2. Always remove jumper before resetting

boiler.

«
...
11
12
13
14
15
...
»

Содержание MultiPulse AM Series

















































Отзывы:

Нет отзывов

Похожие инструкции для MultiPulse AM Series

Бренд: Garanterm Страницы: 20

Бренд: REMEHA Страницы: 60

Бренд: Alpha Страницы: 5

Бренд: Buderus Страницы: 8

Бренд: Mikrofill Страницы: 29

Бренд: PROBOIL Страницы: 44

Бренд: Southbend Страницы: 21

Бренд: ARCA Страницы: 26

PELLEMATIC SmartXS

Бренд: Okofen Страницы: 100

Бренд: Worcester Страницы: 20

Knockdown K-350

Бренд: Bryan Boilers Страницы: 4

Бренд: Knight Страницы: 80

Бренд: Knight Страницы: 80

Бренд: VOKERA Страницы: 8

Бренд: Weil-McLain Страницы: 2

Бренд: Weil-McLain Страницы: 3

Бренд: Weil-McLain Страницы: 11

Бренд: Weil-McLain Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды