Hydrolevel Company FUEL SMART HydroStat 3200-Plus Скачать руководство пользователя страница 3

Страница: 3 / 12

WIRING continued

WARNING

Electrical shock hazard.

To prevent electrical shock, death or equipment damage, disconnect power supply before

installing or servicing this control.

ZONE VALVE WIRING

IMPORTANT:

Use a separate transformer to power zone valves. Connecting zone valves to Z-TV may overload the

HydroStat and cause a lock-out condition (see

Troubleshooting

on page 12 for more information). The total load, including

the burner circuit, vent damper, and Z-TV connections must not exceed 1.2 amps (30 VA). Connect zone valve end-switch
to T/TV as shown below.

STEP 6 For Systems with Indirect Water Heaters

When installing with an indirect water heater, the signal from the indirect must be separated from the heating zone signals and
wired to

and

as shown above. Calls to I1 and I2 will bypass the Thermal Targeting or Outdoor Reset feature and allow the

boiler to fire to the high limit setting to heat the indirect tank.

NOTE:

If you choose not to separate the indirect signal from the heating zones, the Economy Feature should be turned OFF to

insure that the boiler supplies adequate temperature to heat the indirect tank (see page 4).

Содержание FUEL SMART HydroStat 3200-Plus












