background image

VGS600 ASSEMBLY

ASSEMBLY OF 6-SHELF SYSTEM (VGS600)

1.  Take one of the Lower Side Walls (Part A) and lay it down on the floor. Screw two of the Casters 

(Part D or E) into the inserts in the bottom of the Lower Side Wall by hand. Do not overtighten 

the casters.

2.  NOTE: Make sure that both casters are the same type, either with or without brake—both Part D 

or both Part E. 

3.  Slide one of the Upper Side Walls (Part B) onto the lower side wall to build a whole large side 

wall. (TIP: Tap the upper side walls down with a rubber mallet or padded hammer if necessary 

for fully flush seating).

4.  Repeat Step 1 with the other Lower Side Wall and the other two Casters.
5.  Repeat Step 2 with the other Upper Side Wall.
6.  Use a screwdriver or power drill with screwdriver bit to fasten one of the shelves (Part D) to the 

side walls at the bottom holes (closest to the wheels) using four of the provided Shelf Mounting 

Screws (Part G). The smooth side of the shelf should face upward and the side with three 

mounting bars should face downward (toward wheels and floor). This is now the bottom shelf.

7.  Install the Cross Bar (Part C) at the opposite/top end of the Upper Side Walls using two of the 

provided screws. This will give stability to the structure. You can install the cross bar into either 

the front two holes or the back two holes. When the cross bar is installed, it will define the front/

back of the entire rack (when looking at the front, the cross bar should be in the back). 

8.  NOTE: If you choose to position your uppermost shelf at the very top position of the rack, the 

cross bar can instead be installed at a lower point—ideally where the upper and lower side walls 

meet in the middle of the unit.

9.  Install your other five shelves using the provided screws. When installing the shelves, look at 

the notches on the underside to be certain that the shelves are all oriented the same way as the 

bottom shelf is, as this will ensure that when you install light fixtures they will all be consistent 

in their orientation. Multiple shelf mounting holes let you choose the shelf positions that you 

desire.

10.  Get the assistance of a second person to lift the assembled 6-shelf system from the floor to the 

upright position, as it is too heavy and wide to be safely lifted by one. It is now ready for use.

7

Содержание VGS300













Отзывы: