Hydro systems EvoRinse Скачать руководство пользователя страница 13

13

7.1.

Unit is not to be used with any ATEX chemicals.

7.2.

Unit is not to be used with chemicals that may become airborne 

causing a health risk.

7.3.

Unit is not to be used with chemicals outside the temperature 

of 10-50°C.

7.4.

Please use this equipment carefully and observe all warnings 

and cautions.

7.5.

Wear PPE when dispensing chemicals or other materials or 

when working in the vicinity of all chemicals, filling or emptying 

equipment.

                     

7.6.

Always observe safety and handling instructions of the chemical 

manufacturers.

7.7.

Always direct discharge away from you or other persons or into 

approved containers.

7.8.

Always dispense cleaners and chemicals in accordance with 

manufacturer‘s instructions.

7.9.

Always exercise caution when maintaining your equipment.

7.10.

Always re-assemble equipment according to instruction 

procedures. Be sure all components are firmly screwed or 

latched into position.

7.11.

Keep equipment clean to maintain proper operation.

7.12.

You must follow all precautions as advised on the product 

safety data sheet.

7.13.

Before any maintenance, isolate the unit from all power 

supplies.

7.14.

This appliance is not intended for use by persons (including 

children) with reduced physical, sensory or mental capabilities, 

or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance 

by a person responsible for their safety.

7. Safety

Содержание EvoRinse

















Отзывы: