background image

Page 4 of 24

Hydro-Guard® Limited Warranty

 

This Hydro-Guard® Automatic Flushing Device is warranted for one year from the 

date of delivery. Mueller Co. will repair or replace any defective part or component as 
long as the Unit is installed and operated in accordance with the procedures described 
within this manual. Damage or failure caused by the improper installation, assembly, 
disassembly, maintenance or operation of the Hydro-Guard® Automatic Flushing 
Device is not covered by the terms of this warranty. Warranty service is available by 
telephoning Mueller Co. at (877) 864-8500 during regular business hours, or through 
contacting the Hydro-Guard Web Site at www.Hydro-Guard.com.

Hydro-Guard® Safety Procedures and Cautionary Statement

CAUTION

: Failure to read and follow the instructions contained within this manual 

could result in serious personal injury, and/or damage to the Hydro-Guard Automatic 
Flushing Device.

•  Each person involved in the assembly, installation and/or maintenance of the  

Hydro-Guard® Automatic Flushing Device must read this manual carefully 
and follow all instructions prior to performing any installation or maintenance 
procedures involving the Unit. 

•  Verify the drainage path prior to installation to ensure that pedestrian and vehicular 

hazards will not be created by the installation and use of the Hydro-Guard® 
Automatic Flushing Device (In areas in which freezing may occur, special attention 
should be given to this procedure). 

•  Never assemble, disassemble, or perform Hydro-Guard® maintenance unless the 

influent supply valve has been closed, verified and secured, and internal piping 
pressure has been relieved. 

•  Always use all necessary safety equipment and follow all recommended  

procedures when installing, operating and maintaining the Hydro-Guard® 
Automatic Flushing Device. 

•  Perform annual safety inspections and replace worn or defective parts. 

•  Operate the Hydro-Guard® Automatic Flushing Device only when fully installed  

and correctly assembled.

Содержание LongNeck Standard HG-31

























Отзывы: