Hydro-Force Nautilus MX3-200HE Скачать руководство пользователя страница 4

Страница: 4 / 55

Technical Specifications

MX3-200HE High Pressure Extractor

Height: 42-1/4”

(107.32cm)

Length: 34-3/8”

(87.31cm)

Width: 23-3/8”

(59.37cm)

Weight: 123 lbs.

(55.79kg)

Solution Tank Capacity: 12 gallon (45.4 Liters)
Recovery Tank Capacity: 12 gallon (45.4 Liters)

Solution Pump:

Pump-Tec #114T pump with 230v 0.70amp M85 Motor
0-200 psi – 0.89 gpm / 3.37 lpm

Vacuum Motors:

Two AMETEK Lamb 5.7” diameter 3-Stage – tangential discharge
Can be operated in series or parallel configuration

Heater:

2000 Watt 230volt – Dual Element

(Optional)Pump-out Pump:

FloJet 230VAC – 0.75amp - 4.5 gpm

Power Draw:

Cord #1 – 6.03 wide open / 3.93 full load (No Heat)

Cord #2 – 5.30 wide open / 3.20 full load (No Heat)
Cord #1 – 10.20 wide open / 8.10 full load (With Heat)

Cord #2 – 9.47 wide open / 7.37 full load (With Heat)

(Add .75amps to Cord #2 for units with optional Pump-Out Pump)

Standard Equipment
Vacuum Connection:

2” Barb or 2”Male Flash Cuff with 2” Male NPT

Vacuum Hose:

25’ X 1-1/2” with 1-1/2” cuff & 2” cuff

2” Female Flash Cuff x 1-1/2” hose adapter

Accessory Mounting Hardware: Four 1/4-20 x 5/8” SS Screws & Washers
Carpet Wand:

1-1/2” SS Dual Jet S-Bend Wand

– AW29

Pump Priming Hose:

12” x 1/4” with 1/4” male quick connect

HP Solution Hose:

25’ x 1/4” with 1/4” male & female quick connects

Power Cords:

2 – 15M Extension Leads with male & female plug ends

Electrical:

2000W Heater

5amp Pump Circuit Breaker

Internal Component Cooling Fan

Optional Features:
Auto Fill System with chemical draw:
Metering Tip Kit:

14 different tips for changing chemical dilution rate

Water Supply Hose:

50’ x 3/8” with 1/4” female quick connect &
Female garden hose fitting

Auto Pump-out System:
Pump-out Hose:

50’ x 3/4” with male & female garden hose fittings

Содержание Nautilus MX3-200HE
























































Результаты поиска

Содержание Nautilus MX3-200HE

Отзывы:

Похожие инструкции для Nautilus MX3-200HE

Бренды по названию

Популярные бренды

Hydro-Force Nautilus MX3-200HE, Руководство по эксплуатации

Результаты поиска

Содержание Nautilus MX3-200HE

Отзывы:

Похожие инструкции для Nautilus MX3-200HE

Бренды по названию

Популярные бренды