HydraMaster Titan 625 Скачать руководство пользователя страница 155

Страница: 155 / 158

Warranty Information: 11-2

VACUUM AND SOLUTION HOSES

• Failure to protect hoses against freezing.

• Failure to protect hoses against burns from engine and blower exhaust.

• Damage to hoses from being run over by vehicles.

• Kinking or cracking from failure to store or unroll hoses correctly.

• Normal wear and tear from everyday use.

CLEANING WAND AND TOOL

• Failure to protect against freezing.

• Obvious physical abuse of wand or tool.

WATER HEATING SYSTEM

• Over-pressurization of the system (recommended maximum working pressure -

1,200 psi)

• Failure to protect against freezing.

HARD WATER DEPOSITS

• Failure to use or maintain a water softening system or a properly installed magnetic-

type descaler, whichever might be necessary, with machines operating in designated

“Hard Water Areas” (3.0 grains or more per gallon).

WARRANTY PROCEDURE

Warranty coverage is available to you through your local distributor.

If you have moved to a new area or have purchased a used machine and need information

regarding your local distributor, call HydraMaster at (800) 426-1301 or email us at:

[email protected].

When calling your distributor, be sure to have the machine’s information; model and serial

number, ready for the service representative.

Содержание Titan 625































































































































































Результаты поиска

Содержание Titan 625

Отзывы:

HydraMaster Titan 625, Руководство пользователя, Страница: 155 / 158

Результаты поиска

Содержание Titan 625

Отзывы: