HYDAC FILTER SYSTEMS LVU-CD-10 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 68

HYDAC FILTER SYSTEMS LVU-CD-10 Скачать руководство пользователя страница 34

Unit setup/connection

LVU-CD-10

en(us)

Page 34 / 68

BeWa LVU-CD-10 StdPrm 3993633a en-us 2015-08-26.doc

2015-08-26

Checking the water connection / water reservoir

Check the water reservoir for damage. Empty the water reservoir completely
and place the hose from the water outlet into the water reservoir.

NOTE

Excess pressure at the water outlet

The filteration unit will be damaged

►

Guide the water outlet into a depressurized reservoir.

Electrical connection

The filtration unit has a connector cable with a power plug.

DANGER

Exposed electric terminals in the terminal
box of the electric motor

Danger of fatal injury due to electric shock

►

Any work involving the electrical system may

only be done by a properly trained, certified
electrician.

Unwind the connector cable fully. Plug the power plug into a suitable,
earthed, protected power outlet. Match the specifications for the power
supply and frequency on the unit with the network specifications.
The filtration unit has a thermal motor protection switch to protect it from
electrical overload.

«
...
32
33
34
35
36
...
»

Содержание LVU-CD-10





































































Отзывы:

Нет отзывов