manualshive.com logo in svg

Hyd-Mech S-23, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Hyd-Mech S-23 Скачать руководство пользователя страница 70

Pg 49  

S23 2001d

SECTION 9, 

WARRANTY

WARRANTY

Hyd-Mech Saws Ltd. warrants each new S-23 bandsaw to be free from failure resulting from defective material

and workmanship under proper use and service for a period of one year following the date of shipment to the user.
Hyd-Mech's sole obligation under this warranty is limited to the repair or replacement without charge, at Hyd-
Mech's factory, warehouse, or approved repair shop, of any part or parts which Hyd-Mech's inspection shall
disclose to be defective. Return freight must be prepaid by the user.

This warranty, in its entirety, does not cover maintenance items, including but not limited to lubricating grease

and oils, filters, V-belts, saw blades, etc., nor any items therein which show signs of neglect, overloading, abuse,
accident, inadequate maintenance, or unauthorized altering.

MOTOR, GEARBOX, PUMP, ELECTRIC COMPONENTS, VALVES, HOSES, FITTINGS, and any other items

used in the manufacture of the S-23, but not originally manufactured by Hyd-Mech are subject to the original
manufacturer's warranty. Hyd-Mech will provide such assistance and information as is necessary and available to
facilitate the user's claim to such other manufacturer.

Liability or obligation on the part of Hyd-Mech for damages, whether general, special or for negligence and

expressly including any incidental and consequential damages is hereby disclaimed.

Hyd-Mech's obligation to repair or replace shall be the limit of its liability under this warranty and the sole and

exclusive right and remedy of the user.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

WRITTEN OR ORAL, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILI-
TY OR FITNESS FOR A PARTICULAR PURPOSE.

This warranty may not be changed, altered, or modified in any way except in writing by Hyd-Mech Group Ltd.

HYD-MECH GROUP

1079  Parkinson Road

P.O. BOX 1030

Woodstock, Ontario

N4S 8P6

Phone: (519) 539-6341
Fax:      (519) 539-5126

Toll Free (800) 276-SAWS (7297)

e-mail, [email protected]

Содержание S-23








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды