HYCON HH10 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 23

HYCON HH10 Скачать руководство пользователя страница 4

3

•

The operator must always use protective goggles, earplugs, hard hat and shoes
when operating the breaker.

•

Never use the breaker close to electric cables. Prior to operation, check whether
there are hidden or buried cables in the ground.

•

Never wear loose clothing as it may get entangled in the moving parts of the
breaker.

•

Inspection or cleaning of the breaker, change of chisel or disconnection of hoses
may never be done while the breaker is connected to the powerpack, as uninten-
tional activation of the breaker can cause severe damage.

•

Always connect hoses to the breaker before starting the powerpack. Be sure that
all couplings are tight.

•

The breaker may not be operated if the oil temperature is above 70 C°. Operation
at higher temperatures may result in the breaker getting warmer than normal and
the operator risks getting burnt on it.

•

To avoid all personal injury and damage to material, all repair, maintenance and
service work must be carried out by authorized or properly trained persons only.

«
...
2
3
4
5
6
...
»

Содержание HH10
























Отзывы:

Нет отзывов