HYCON HCS14 Pro Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 26

background image

22

Mounting

Add Loctite 243 to the two threads in the safety trigger, and mount the leaf spring
with the two screws. Insert the safety trigger in the handle and push the pin w/hole
through the handle and safety trigger. Insert the trigger lever in the handle and
mount the pin through handle and trigger lever. Mount the retaining rings on both
sides of the pin. Place the entire handle on a firm surface so that the pin does not
slip out when hammering on it. With a hammer and a punch expand the hole in the
pin so that the pin is firmly secured. Do this from both sides.

«
...
21
22
23
24
25
...
»

Содержание HCS14 Pro



























Отзывы:

Нет отзывов

Похожие инструкции для HCS14 Pro

Бренд: Hafco Metalmaster Страницы: 34

Бренд: Palmgren Страницы: 28

Бренд: Scheppach Страницы: 88

Бренд: Stanley Страницы: 30

Бренд: GreenWorks Страницы: 32

Бренд: GreenWorks Страницы: 28

Бренд: Casals Страницы: 84

Бренд: Ozito Страницы: 16

Бренд: Wood-mizer Страницы: 135

Бренд: KRESS Страницы: 104

Бренд: GMC Страницы: 64

Бренд: Haussmann Страницы: 15

Бренд: TTMC Страницы: 18

Бренд: TigerStop Страницы: 52

Бренд: Hydmech Страницы: 4

Бренд: SCM Страницы: 155

Бренд: Wadkin Страницы: 34

Бренд: YILMAZ Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды