background image

• 

Refer to Diagram 4 . The chiller should be installed after the t-piece and drinking 

water filter, before the filtered drinking water tap connection. 

• 

Two identical connectors are provided to connect the ¼” tubing to the ‘WATER IN’ 

inlet on the chiller and then to connect a new run of ¼” tubing from the ‘WATER OUT’ 

outlet of the chiller to the tap.

• 

Ensure all tubing is pushed fully into PF connectors and that locking collars are used 

to prevent inadvertant removal.

• 

Select a suitable location for the drinking water filter housing ensuring easy access 

for future maintenance.

• 

Do not locate the filter above an electrical socket or other electrical device.

• 

Remove drinking water filter from housing and secure the bracket to the wall using 

fixings supplied. Replace the filter cartridge by pushing up into the housing and 

turn towards the ‘close’ position.

• 

Use a suitable length of ¼” tubing to connect from remaining outlet of t-piece to 

drinking water filter inlet marked ‘IN’.  

• 

Use a suitable length of ¼” tubing to connect drinking water filter outlet marked 

‘OUT’, one of the identical connectors and a black washer (provided with the chiller) 

to facilitate connection to ‘WATER IN’. 

• 

Use remaining identical connector and a black washer (provided with the chiller) to 

facilitate connection from ‘WATER OUT’. 

• 

Use a suitable length of ¼” tubing to connect chiller outlet marked ‘OUT’ to cold inlet 

of Spa tap using ¼” x ¼” PF connector.

• 

It is recommended that the lowest setting (1) is used for drinking water.  A higher 

setting will cause the unit to work harder and in turn increase the temperature of 

the installation environment. 

Ensure you read separate chiller instructions for all important safety points and 

instructions before installation.

Before commencing installation, ensure the location is a flat level surface that will 

allow for adequate airflow around all sides of the appliance.

2. Install Optional Water Chiller with Cold Drinking Water Filter

14

Содержание Zen Spa Series


























Отзывы: