background image

06 = 30 storage units are available 
07 = 35 storage units are available 
08 = 40 storage units are available 
09 = 45 storage units are available 
10 = 50 storage units are available 
………. 
50 = 250 storage units are available 
(Note: Total number of recording blocks is 250 for 32MB capacity; and 590 for 64MB capacity) 

 

In this example Station 112 has been allocated 15 storage units which is 7.5 minutes of recording time. The 
Mailbox has also been set in item 06 to a maximum message length of  1 minute using the following table. 

 
Default = 0 (no limit) 
01 = 1 storage unit 
02 = 2 storage units 
03 = 3 storage units 
04 = 4  storage units 
….. 
90= 90 units (max.) 

 

ON systems with PSTN lines where Reversal on idle is not fitted then it is most important that a maximum 
time is allocated for a mailboxes message otherwise if a caller hangs up without pressing #  the recording 
will continue until the mailbox is full and then the system will clear the call down. If the maximum time is 
set to 1 minute then if the caller neglects to press # the mailbox will only record until the message is 1 
minute long then clear down the call.  

 
 
 
 
 
 
 
 
 
 

 
 
 
 

Содержание G2-VMU










Отзывы: