HWH SPACEMAKER Скачать руководство пользователя страница 27

Страница: 27 / 27

ML60078/MP84.9999

16APR19

RELEASE

NUT

NOTE: When opening the
valve DO NOT turn the valve
release nut more than 4 and
1/2 turns counter clockwise.

OIL LEVEL

1/4" NUT DRIVER

THE BREATHER CAP IS
LOCATED ON THE TOP

TOP OF THE RESERVOIR. BEFORE RETURNING THE

BREATHER CAP TO THE RESERVOIR, REMOVE ANY

counter clockwise. Damage to

nut more than 2 full turns

NOTE: When opening the valve
DO NOT turn the valve release

REMOVE TO GAIN
ACCESS TO THE 1/4"
VALVE RELEASE NUT

2 1/4" DIAMETER SOLENOID VALVE

1 1/2" DIAMETER SOLENOID VALVE

GROOVES

SIDE OF THE POWER
UNIT RESERVOIR

NOTE: The cam release may be
rotated in any direction on the
valve. DO NOT assume that
pushing down will open the

1 1/2" DIAMETER SOLENOID VALVE

valve. Pushing the cam in the

2 1/4" DIAMETER SOLENOID VALVE

the valve may result.

Damage to the valve may

FILL BETWEEN

SOLENOID VALVES WITH CAM RELEASE

wrong direction could damage
the valve.

NOTE: The cam release may be
rotated in any direction on the
valve. DO NOT assume that
pushing down will open the
valve. Pushing the cam in the
wrong direction could damage
the valve.

result.

WIRE TIE

HYDRAULIC SOLENOID VALVE

INFORMATION/INSTRUCTION SHEET

INDENTIFICATION - MANUAL OPERATIONS - REPLACEMENT

Manual retract

VALVE OPEN

CAM RELEASE

Default position

VALVE CLOSED

CAM RELEASE

Default position

VALVE CLOSED

position

CAM RELEASE
VALVE OPEN

position

Manual retract

REPLACEMENT VALVES WILL HAVE A VALVE RELEASE CAM

SOLENOID VALVES WITH 1/4" NUT RELEASE

1/4" NUT DRIVER, CLEAN ANY DEBRIS FROM THE

CAP, EITHER TO CHECK THE OIL LEVEL OR TO USE

IMPORTANT: PRIOR TO REMOVING THE BREATHER

INCLUDING DEBRIS INSIDE THE 1/4" NUT DRIVER.

PLASTIC PLUG:

PAINT CHIPS OR OTHER DEBRIS FROM THE DIPSTICK

VALVE

NUT

RELEASE

VALVE

open the valve. Do not over tighten
when closing.

approximately 4 1/2 turns to fully

compresses a spring. It takes

turn easy at first, then harder as it

open the valve. T-handle should

Turn T-handle counterclockwise to

BREATHER CAP W/NUT DRIVER

SOLENOID VALVES WITH T-HANDLE RELEASE

NOTE: OLD STYLE HEX SHAPED
SOLENOID VALVES HAVE NO MANUAL
VALVE RELEASE.

2 1/4" DIAMETER SOLENOID VALVE

Содержание SPACEMAKER




























Результаты поиска

Содержание SPACEMAKER

Отзывы:

Похожие инструкции для SPACEMAKER

Бренды по названию

Популярные бренды

HWH SPACEMAKER, Руководство оператора

Результаты поиска

Содержание SPACEMAKER

Отзывы:

Похожие инструкции для SPACEMAKER

Бренды по названию

Популярные бренды