background image

MAINTENANCE

MP44.0018

13NOV17

OIL LEVEL

ELECTRICAL SYSTEM

The batteries should be in good condition and fully charged.
Weak batteries can cause erratic operation.  Battery cable 
terminals and battery posts and connections should be kept 

All electrical connections, especially ground connections, 
should be clean, tight, free from corrosion and protected 

JACKS

There are very few user serviceable parts on the jacks
The jacks require very little maintenance.  If the jacks are

VISUAL INSPECTION

Periodically inspect the system for oil leaks and 
damaged or missing parts, such as pivot bolts or springs.
Check the hydraulic lines and wiring for damage and wear.  
Check that the jacks do not interfere with any parts of the 
vehicle when they are in the "STORE" position.

The system will operate better if kept clean and free 
from caked on mud or ice.

OPERATIONAL CHECK

Check that all lights work according to the "INDICATOR 
LIGHT" Section.  Correct function of the red "WARNING" 

Review the OPERATOR MANUAL.  Run the system 
according to the SYSTEM OPERATION Section.  
Note any abnormal operation.

Review the "JACK RETRACTION" Section.  Make sure the 
jacks will fully retract to the "STORE" position.  Jacks should 
not interfere with any of the coach when in the "STORE"

clean.

from weathering.

light is important.

position.

extremely dirty with caked on mud they should be washed.

If extremely dirty, the jack rods should NOT be wiped. The 
jack rods do not need to be oiled or sprayed with anything.

ROOM EXTENSIONS

The HWH room mechanisms need no maintenance.
DO NOT grease or lubricate any parts of the HWH
mechanism.

Any visible mechanism can be kept clean by washing
with water.  Refer to the vehicle manufacturer for
correct maintenance of the room seals.

See ML47149 for proper maintenance of all jacks.

cap before removing.

and steps should be fully retracted before checking fluid

breather cap.  Clear any dirt away from the breather / filler

assembly.  The oil level is checked and filled through the

level.  The oil reservoir is part of the pump / manifold

Any HWH hydraulic equipment, including jacks, slide-outs

servicing of the coach.

All maintenance should be done as part of the normal 

there is an oil leak in the system.

purchased and then once every two years.  More often if 

The oil level should be checked when the vehicle is first 

should be between the bottom of the dipstick and the

reservoir. Most breather caps have a dipstick.  Fluid level

The oil  level should be within one inch of the top of the

emergency Dexron automatic transmission fluid can be used.

Dexron automatic transmission fluid contains red dye

and can cause staining should a leak occur.  DO NOT USE
brake fluid or hydraulic jack fluid.  Use of these can damage 

HWH Specialty Hydraulic Oil is recommended.  In an

NOTE: Overfilling the tank can cause leakage of oil 
through the breather cap.

center mark.

FLUID:

NOTE:

seals.

Содержание SPACEMAKER




























Отзывы: