HUSTLER Hustler Z 926253 Скачать руководство пользователя страница 5

350157  Rev 11/02

1-1

This manual applies to the following equipment:

Hustler Z tractor & 60” deck, number 926253
Hustler Z tractor & 60” deck, number 926295
Hustler Z tractor & 52” deck, number 926311
Hustler Z tractor & 52” deck, number 926345
Hustler Z tractor & 60” deck, number 926451
Hustler Z tractor & 60” deck, number 926469
Hustler Z tractor & 72” deck, number 926550
Hustler Z tractor & 72” deck, number 926568
Super Z tractor & 60” deck, number 926360
Super Z tractor & 60” deck, number 926378
Super Z tractor & 52” deck, number 926485
Super Z tractor & 52” deck, number 926493
Super Z tractor & 72” deck, number 926436
Super Z tractor & 72” deck, number 926444

To the new owner

The purpose of this manual is to assist owners and

operators in maintaining and operating the Hustler Z tractor
and deck.  Please read it carefully; information and
instructions furnished can help you achieve years of
dependable performance.

A separate Engine Manual is included with your owner’s

packet which contains additional engine information that
will not be repeated in this manual.  You are urged to read it
before attempting any operation or repair of the engine.

The Quick Reference Decals, located under the right front

of the seat, the right front of the deck, and under the seat
pan, are designed to give the operator brief information
needed in the daily operation of the machine.  These decals
are not intended to be used in place of this manual but
instead is to be used as an extension of this manual.  These
decals should not be removed or obliterated.  Replace these
decals if they become unreadable.  

It is the owner’s responsibility to make certain that the

operator reads and understands this manual and the Quick
Reference Decals before operating this machine.  It is also
the owner’s responsibility to make certain that the operator
is a qualified and physically able individual, properly
trained in the operation of this equipment.  Local regulations
may restrict the age of the operator.

Using this manual

General operation, adjustment and maintenance guidance

is outlined for both the experienced and novice Hustler user.
Operating conditions vary considerably and cannot all be
addressed individually.  Through experience, however,
operators should find no difficulty in developing good
operating skills suitable to most conditions.

Directions used in this manual, for example RIGHT or

LEFT, refer to directions when seated on tractor facing
forward, unless otherwise stated.

Photographs and illustrations used were current at the

time of printing, but subsequent production changes may
cause your machine to vary slightly in detail.  Hustler Turf
Equipment reserves the right to redesign and change the
machine as deemed necessary, without notification.  If a
change has been made to your machine which is not
reflected in this owner’s manual, or the parts manual, see
your Hustler dealer for current information and parts.

Warranty registration

The Delivery and Warranty Registration form must be

completed and signed to validate your warranty protection.
As the new equipment owner, you are expected to see that
the form is completed and forwarded to Hustler Turf
Equipment at time of delivery.

Be sure to register the tractor plus each attachment that

displays a model and serial identification number plate with
Hustler Turf Equipment.

IMPORTANT:

Any unauthorized modification,

alteration, or use of non-approved attachments voids the
warranty and releases Hustler Turf Equipment from any
liability arising from subsequent use of this equipment. 

Model and serial number

Tractor model and serial numbers are found on the serial

identification plate, located on the frame directly below and
to the left of the operator’s platform.

These numbers are required on the Warranty Registration

form.  They will also assure you of the correct service parts
when replacement becomes necessary.

Parts and service

Use original Hustler replacement parts only.  These parts

are available through your local Hustler dealer.  To obtain
prompt, efficient service, always provide the following
information when ordering parts:

1. Correct part description
2. Correct model number.
3. Correct serial number.

All warranty repair and service must be handled through

an authorized Hustler dealer.  Arrangements should be made
through your local service center.

For location of nearest dealer, or should you need further

assistance, contact:

Customer Service Department
Hustler Turf Equipment
P.O. Box 7000
Hesston, KS  67062
Telephone (620) 327-4911
FAX (620) 327-2458

GENERAL INFORMATION

Содержание Hustler Z 926253














































Отзывы: