background image

P/N 3018126_E 

4-1

HUSSMANN CORPORATION • BRIDGETON, MO  63044-2483  U.S.A.

SMG8B & SSG8B

3-10

 

s

tartup

 / o

pEratIon

P/N 3018126_E 

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • www.hussmann.com

P/N 3018126_E 

4-1

HUSSMANN CORPORATION • BRIDGETON, MO  63044-2483  U.S.A.

SMG8B & SSG8B

CARE AND CLEANING  

Long life and satisfactory performance of 
any equipment is dependent upon the care it 
receives. To ensure long life, proper sanitation 
and minimum maintenance costs, these  
merchandisers should be thoroughly cleaned, 
all debris removed and the interiors washed 
down, weekly. 

Exterior Surfaces

The exterior surfaces must be cleaned with a 
mild detergent and warm water to protect and 
maintain their attractive finish. 

n

ever

 

use

 

AbrAsive

 

cleAnsers

 

or

 

scouring

 

pAds

.

Interior Surfaces

The interior surfaces may be cleaned with most 
domestic detergents, ammonia based cleaners 
and sanitizing solutions with no harm to the 
surface. Self contained models empty into a 
limited capacity evaporation pan, which will 
overflow if excess water is used in cleaning.

Do NOT Use:

•Abrasive cleansers and scouring pads, as these 
will mar the finish.

•Coarse paper towels on coated glass.

•Ammonia-based cleaners on acrylic parts.

•Solvent, oil or acidic based cleaners on any  
interior surfaces.

•Do not use high pressure water hoses.

Do:

•Remove the product and all loose debris to 
avoid clogging the waste outlet.

•Store product in a refrigerated area such as a  
cooler. Remove only as much product as can 
be taken to the cooler in a timely manner.

•Disconnect electrical power before cleaning.

•Thoroughly clean all surfaces with soap and 
hot water. 

d

o

 

not

 

use

 

steAm

 

or

 

high

 

wAter

  

pressure

 

hoses

 

to

 

wAsh

 

the

 

interior

.

 

t

hese

 

will

 

destroy

 

the

 

merchandisers

’ 

sealing

 

causing

 

leaks

 

and

 

poor

 

performance

.

•Take care to minimize direct contact between 
fan motors and cleaning or rinse water.
•Do NOT flood merchandiser with water. 

n

ever

 

introduce

 

wAter

 

fAster

 

thAn

 

the

 

wAste

 

outlet

 

cAn

 

remove

 

it

.  

stAndArd

 

cAses

 

Are

 

equipped

 

with

 

A

 

floor

 

drAin

An

 

optionAl

 

drAin

 

kit

 

is

 

AvAilAble

•Allow merchandisers to dry before resuming 
operation.

•After cleaning is completed, turn on power to 
the merchandiser.

MAINTENANCE

Product will be degraded and may spoil if 

allowed to sit in a non-refrigerated area.

Do NOT allow cleaning agent or 

cloth to contact food product.

Содержание SSG8B







































Отзывы: