background image

PAGE 12

 

MPD GLASS DOOR MULTIDECK - HUSSMANN

 

•  Model No: 

Identifies the model type (letters on left) 

as well as the model size (numbers on right)

•  Serial Number: 

The unique number given to each 

case. 

•  Asset Code: 

Optional identification number for 

supermarket stores. 

•  Project: 

Used to identify location site for the case

•  SO Number: 

Sales Order number

•  PO Number: 

Purchasing Order Invoice number

•  Department Type: 

The type given for 

merchandising location, eg bakery, dairy, deli etc.

•  Model : 

Identifies the model type (letters on left) as 

well as the model size (numbers on right)

•  Climate Class: 

The climate class relates to the 

atmospheric, or ambient conditions outside the 

fridge or freezer. These conditions determine 

how much energy the unit will utilise in specific 

environments.

•  Net Volume: 

The net volume is the total space 

inside the case.

•  Refrigerant: 

Identifies the refrigerant used in the 

case.

•  Voltage: 

Voltage is the amount of potential energy 

between two points on a circuit. This is measured 

in volts (V).

•  Fans Current:

 The fans

 

flow of electricity which 

results from the ordered directional movement of 

electrically charged particles, measured in Amps 

(A).

•  Asset Code: 

Optional identification number for 

supermarket stores. 

•  Anti-Sweat Current: 

The heater thats installed 

in the frames and doors of refrigerated cases to 

reduce condensation and prevention fogging, this 

is measured in Amps (A).

•  Defrost and Drain Current; 

The current from 

heaters that are installed in freezer cases to stop the 

case  from icing up, measured in Amps(A).

•  Dimensions: 

The sizing of the case measured in 

milimeters(mm) L x W x H. 

•  Type: 

The type given for merchandising location, 

eg bakery, dairy, deli etc.

•  Net Weight: 

The net weight is the total weight 

including shelving and all part supplied with the 

case.

•  Date of Manufacture: 

The date of build.

•  Frequency: 

Frequency is the rate at which current 

changes direction per second. It is measured in 

Hertz (Hz), an international unit of measure where 1 

Hertz is equal to 1 cycle per second.

•  Lights Current: 

The total current of the lighting 

modules in a case, measured in Amps (A).

•  Configuration ID: 

Identifies the model type, model 

size, the lineup number and the case sequence 

number.

•  Serial Number: 

The unique number given to each 

PACKAGING TAG:

RATING PLATE:

ASSET CODE: 

RATING PLATE (Continued):

PRE INSTALLATION

 

Содержание MPD116














































Отзывы: