background image

Elite 

Medium Temperature

P/N 0453523

1-1

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483  U.S.A.

NSF CERTIFICATION

These merchandisers are manufactured to meet
ANSI / National Sanitation Foundation (NSF

®

)

Standard #7 requirements. Proper installation is
required to maintain certification. Near the serial
plate, each case carries a label identifying the type
of application for which the case was certified.

ANSI

/

NSF-7 Type I – Display Refrigerator / Freezer

Intended for 75°F / 55%RH Ambient Application

ANSI

/

NSF-7 Type II – Display Refrigerator / Freezer

Intended for 80°F / 55%RH Ambient Application

ANSI

/

NSF-7 – Display Refrigerator 

Intended for Bulk Produce

LOCATION

These merchandisers are designed for displaying
products in air conditioned stores where tempera-
ture is maintained at or below the ANSI / NSF-7
specified level and relative humidity is maintained
at or below 55%. 

Placing refrigerated merchandisers in direct sun-
light, near hot tables or near other heat sources
could impair their efficiency.

Like other merchandisers, these are sensitive to
air disturbances. Air currents passing around
merchandisers will seriously impair their opera-
tion. Do NOT allow air conditioning, electric
fans, open doors or windows, etc. to create air
currents around the merchandisers.

Product should always be maintained at proper
temperature. This means that from the time the
product is received, through storage, preparation
and display, the temperature of the product must
be controlled to maximize the life of the product.

The exterior frames on these cases provide space
for air circulation. However, in high ambient 
conditions, sweating may still occur. If this 
happens install a method of forced ventilation
such as a fan ventilation kit.

SHIPPING DAMAGE

All equipment should be thoroughly examined for
shipping damage before and during unloading.

This equipment has been carefully inspected at
our factory. Any claim for loss or damage must be
made to the carrier. The carrier will provide any
necessary inspection reports and/or claim forms.

Apparent Loss Or Damage

If there is an obvious loss or damage, it must be
noted on the freight bill or express receipt and
signed by the carrier’s agent; otherwise, carrier
may refuse claim. 

Concealed Loss Or Damage

When loss or damage is not apparent until after
equipment is uncrated, retain all packing materials
and submit a written request to the carrier for
inspection, within 15 days.

EXTERIOR LOADING

Do NOT walk on top of merchandisers

or

damage to the merchandisers and serious 
personal injury could occur. T

HEY ARE NOT

STRUCTURALLY DESIGNED TO SUPPORT EXTERNAL

LOADING

such as the weight of a person. Do not

place heavy objects on the case.

INSTALLATION

Do not walk or put heavy objects on case.

CAUTION

!

Содержание IMPACT Elite E1































Отзывы: