Hussmann HGM-1 BS Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 70

background image

99-16105-S001_A

5/20/2010

Instuctions

16

14. Using a plastic mallet and a flat-head screwdriver, remove the torque rod from the bottom of the door assembly.

Refer to figure

(I)

15. Swap placement of the Hinge Pin and Torque Rod to the other’s original mounting hole in the door assembly hinge

side rail.

  16.   Reinstall the hinge pin and the torque rod completely into the ends of the door assembly hinge rail.
  17.   If necessary, lightly tap on the hinge pin and torque rod with a plastic or rubber mallet until each is fully seated into

the top and bottom of the door.

  18.   Reconnect the hinge in wires and confirm that all connections are secure.
  19.   Check and confirm torque rod and hinge pin are correctly and completely installed.
  20.   Reinstall the door into the frame.

NOTE: Refer to www.anthonydoors.com for complete door/frame installation instructions.

I

«
...
58
59
60
61
62
...
»

Содержание HGM-1 BS







































































Отзывы:

Нет отзывов

Похожие инструкции для HGM-1 BS

Бренд: Hussmann Страницы: 6

Бренд: Howard McCray Страницы: 3

Бренд: YATO Страницы: 36

Бренд: Barker Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды