background image

OPERATION  AND  MAINTENANCE

SERVICING DATA AND

PROCEDURES

OPERATION   and

MAINTENANCE

TEMPERATURE  CONTROL –

The thermostat, which senses the cold
wall  temperature,  is located  at the  lower
rear  right  corner  of the  cabinet through
the  access panel.   It has  been  pre-set at
the

factory

to

maintain

product

temperatures  between  +10°  and  +4°. The
thermostat is adjustable.

If other than

normal  temperatures  are  required, adjust
the  control  by  turning  the  knob  clockwise
for

colder

and

counter-clockwise

for

warmer  temperatures.

DISPLAY  LIGHTING –

All  models  are  equipped  with fluorescent
light  fixtures  installed  in  the  canopy. An
ON-OFF switch is located in the right
service side of the canopy and is so
labeled.

ANTI-SWEAT  HEATERS –

A resistance heater is installed in the
perimeter  of the base frame of the canopy
to prevent condensation.

Continuity of

the  heater  circuit  maybe  checked  at  the
splice  located  inside  the  ballast enclosure
in  the  compressor  compartment.

Should the heater fail it may be replaced

by:

Raise  top  and canopy as an assembly
and  place  wood  spacers  between top
and  cabinet.

Remove

heater

from

under

base

frame.

Disconnect  spade  terminal  splices  and
remove.

Reassemble  reverse  order  – resistance
heater  wire  must  be  taped  back into
position

DEFROSTING –

It  must  be  recognized  that accumulation
of frost  on  the  cabinet  walls  does impair
refrigeration.

Daily

scraping

of

the

interior  walls  with  a  plastic  scraper  will
extend

the

length

of

time

between

complete  defrosting.

Most  installations  will require  a complete
defrosting

every

seven

to

ten

days.

Usually  the  best  time  to  defrost is  at the
close of business so the cabinet will be
regulated for the start of the next  business
day.

The  ice  cream  should  be  removed from
the cabinet and placed in a walk-in or
storage

freezer

during

the

defrosting

operation.

A power switch for turning

the case off for defrosting is located
through  the  access  panel.

Remove  screws  holding  aluminum  top
to  cabinet.

Defrosting  may  be  accomplished  with the
aid of a hair  dryer, plastic scraper  or by
merely letting the cabinet remain open
until the  walls  are cleared.   Care  should

6

Содержание DCCG-12



















Отзывы: