r3(Cr3)-m/f-0608
0
User information
replacing fluorescent lamps
Fluorescent lamps are furnished with a shatterproof
protective coating. The same type of lamp with protective
coating must be used if replaced.
ENCAPSULITE
SHATTERPROOF COATING - SA 10645
Complies with FDA USDA
& OSHA Regulations
for replacement call:
1-800-395-9229
Turn switch off then on after replacing bulb
NSF
U R
R
evaporator fans
The evaporator fans are located at the center front of these
merchandisers directly beneath the display pans.
Should
fans or blades need servicing, always replace fan blades
with the raised embossed side of the blade TOWARD THE
MOTOR.
Copper Coils
The copper coils used in Hussmann merchandisers may
be repaired in the field. Materials are available from local
refrigeration wholesalers.
Hussmann recommends using #15 Sil-Fos for repairs.
aluminum Coils
The aluminum coils should be replaced if damaged.
non-glare glass (optional)
The high optical clarity of this glass is possible due to
special coatings on the glass surface itself. To preserve this
coating and the optical clarity, keep the glass clean.
Water is the only solution recommended to be used to
clean the non-glare glass. The damage to the glass from
improper, caustic solutions is irreparable.
In addition to cleaning the glass with the recommended
product, there are precautions that should be taken when
working and cleaning the inside of the case.
• When cleaning the inside of the cases, we
recommend that the glass be fully opened and
covered to prevent to prevent solutions from
splashing onto the glass and ruining the coating on
the inside.
• Only use a soft cloth and water (in a spray bottle) for
cleaning any glass or mirrored components. Be sure
to rinse and/or dry completely.
•
never use hot water on cold glass surfaces!
it may shatter and cause serious injury!
Allow
glass surfaces to warmed to room temperature.
Plexiglass and acrylic Care
Improper cleaning not only accelerates the cleaning cycle
but also degrades the quality of this surface. Normal daily
buffing motions can generated static cling attracting dust
to the surface. Incorrect cleaning agents or cleaning cloths
can cause micro scratching of the surface, causing the
plastic to haze over time.
Cleaning
Hussmann recommends using a clean damp chamois, or a
paper towel marketed as dust and abrasive free with
210
®
Plastic Cleaner and Polish
available by calling Sumner
Labs at
1-800-542-8656
. Hard, rough cloths or paper towels
will scratch the acrylic and should not be used.
antistatic Coatings
The product
210
®
has proven to be very effective in not
only cleaning and polishing the Plexiglass surface, but also
providing anti-static and anti-fog capabilities. This product
also seals pores and provides a protective coating.
tips and troubleshooting
before calling for service, check the following:
1. Check electrical power supply to the equipment for
connection.
2. Check fixture loading. Overstocking case will affect
its proper operation.
3. If frost is collecting on fixture and/or product, check
that no outside doors or windows are open allowing
moisture to enter store. These merchandisers were
designed for use in stores were temperature &
humidity does not exceed 75° F and 55% H.
4. If front self-service case is not performing check
proper installation of lower deck pan refer to case
cleaning section.
Case Cleaning
Long life and satisfactory performance of any equipment
are dependent upon the care given to it. To insure long life,
proper sanitation and minimum maintenance costs, the
refrigerator should be thoroughly cleaned frequently.
SHUT OFF FAN DURING CLEANING PROCESS. It can be
unplugged within the case, or shut off case at the source.
The interior bottom may be cleaned with any domestic
soap or detergent based cleaners. Sanitizing solutions
will not harm the interior bottom, however, these solutions
should always be used according to the manufacturer’s
directions.
It is essential to establish and regulate cleaning procedures.
This will minimize bacteria causing discoloration which
leads to degraded product appearance and significantly
shortening product shelf life.
Soap and hot water are NOT enough to kill this bacteria. A
sanitizing solution MUST be included with each cleaning
process to eliminate this bacteria.
Remove all food stuffs, ice, debris, etc., and either access
the case from the rear or the front of the case. Allow the
case to come to room temperature.