background image

ASC-LG / ASCS-LG-0506

product in determining if the refrigerator will be allowed 
to display potentially hazardous food. For the purpose 
of this evaluation, product temperature above the FDA 
Food Code 1993 temperature for potentially hazardous 
food will be the first indication that an evaluation should 
be performed. It is expected that all refrigerators will 
keep food at the FDA Food Code 1993 temperature for 
potentially hazardous food.

1.1  The following recommendations are made for the 

purpose of arriving at easily taken and understood 

data which, coupled with other observations, may 

be used to determined whether a display refrigera-

tor is working as intended:

a)  INSTRUMENT – A stainless steel stem-type 

thermometer is recommended and it should 

have a dial a minimum of 1 inch internal diam-

eter. A test thermometer scaled only in Celsius 

or dually scaled in Celsius and Fahrenheit shall 

be accurate to 1°C (1.8°F). Temperature mea-

suring devices that are scaled only in Fahren-

heit shall be  accurate to 2°F. The thermometer 

should be checked for proper calibration. (It 

should read 32°F when the stem is immersed 

in an ice water bath).

b)  LOCATION – The probe or sensing element 

of the thermometer should be located in the 

airstream where the air first enters the display 

or storage area, and not more than 1 inch 

away from the surface and in the center of the 

discharge opening.

c)  READING – It should first be determined that 

the refrigerator is refrigerating and has oper-

ated at least one hour since the end of the 

last defrost period. The thermometer reading 

should be made only after it has been allowed 

to stabilize, i.e., maintain a constant reading.

d)  OTHER OBSERVATIONS – Other observations 

should be made which may indicate operat-

ing problems, such as unsatisfactory product, 

feel/appearance.

e)  CONCLUSIONS – In the absence of any ap-

parent undesirable conditions, the refrigerator 

should be judged to be operating properly. If it 

is determined that such condition is undesir-

able, i.e., the product is above proper tempera-

ture, checks should be made for the following:

1.  Has the refrigerator been loaded with warm 

product?

2.  Is the product loaded beyond the “Safe Load 

Line” markers?

3.  Are the return air ducts blocked?

4.  Are the entering air ducts blocked?

5.  Is a dumped display causing turbulent air flow 

and mixing with room air?

6.  Are spotlights or other high intensity lighting 

directed onto the product?

7.  Are there unusual draft conditions (from heat-

ing /air-conditioning ducts, open doors, etc.)?

8.  Is there exposure to direct sunlight?

9.  Are  display  signs  blocking  or  diverting  air-

flow?

10.  Are the coils of the refrigerator iced up?

11.  Is the store ambient over 75°F, 55% RH as set 

forth in ASHRAE Standard 72 and ASHRAE 

Standard 117?

12.  Are the shelf positions, number, and size other 

than recommended by the manufacturer?

13.  Is  there  an  improper  application  or  control 

system?

14.  Is  the  evaporator  fan  motor/blade  inopera-

tive?

15.  Is the defrost time excessive?

16.  Is the defrost termination, thermostat (if used) 

set too high?

17. Are  the  refrigerant  controls  incorrectly  ad-

justed?

18.  Is the air entering the condenser above design 

conditions? Are  the  condenser  fins  clear  of 

dirt, dust, etc.?

19.  Is there a shortage of refrigerant?

20.  Has  the  equipment  been  modified  to  use 

replacements for CFC-12, CFC-502 or other 

refrigerant? If so, have the modifications been 

made in accordance with the recommendations 

of Hussmann’s equipment ? Is the refrigerator 

charged with the proper refrigerant and lubri-

cant? Does the system use the recommended 

compressor?

APPENDIX D. – Recommendations to 
user - 

1.0  Hussmann should provide instructions and recom-

mendations for proper periodic cleaning. The user 

will be responsible for such cleaning, including the 

cleaning of low temperature equipment within the 

compartment and the cooling coil area(s). Cleaning 

practices, particularly with respect to proper refrig-

erator unloading and warm-up, must be in accor-

dance with applicable recommendations.

1.1  Cleaning of non Gelato equipment should include a 

weekly cleaning of the food compartment as a mini-

mum to prevent bacteria growth from accumulating. 

Actual use and products may dictate more frequent 

cleaning. Circumstances of use and equipment 

design must also dictate the frequency of cleaning 

Appendices, Cont’d

Содержание ASC-LG





































Отзывы: