Husqvarna TE 250 страница 136 Скачать руководство пользователя

Страница: 136 / 169

18 SERVICE WORK ON THE ENGINE

134

18.5

Checking the gear oil level

Info

The gear oil level must be checked when the engine is cold.

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

F02322-10

Main work

–

Remove gear oil level monitoring screw

–

Check the gear oil level.

A small quantity of gear oil must run out of the drilled hole.

» If no gear oil runs out:

–

Add the gear oil.

(

p. 135)

–

Mount and tighten the gear oil level monitoring screw.
Guideline

Screw, gear oil level

monitoring

8 Nm (5.9 lbf ft)

18.6

Changing the gear oil

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

–

Wear suitable protective clothing and safety gloves.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Drain the gear oil while the engine is at operating temperature.

Preparatory work

–

Remove the engine guard. (

p. 85)

–

Park the motorcycle on a level surface.

–

Position an appropriate container under the engine.

F02323-10

Main work

–

Remove gear oil drain plug

with magnet.

–

Let the gear oil drain fully.

–

Thoroughly clean the gear oil drain plug with magnet.

–

Clean the sealing surface on the engine.

–

Mount and tighten gear oil drain plug

with the magnet

and a new seal ring.
Guideline

Gear oil drain plug

with magnet

M12x1.5

20 Nm (14.8 lbf ft)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды