Husqvarna TE 250 Скачать руководство пользователя

Страница: 87 / 169

SERVICE WORK ON THE CHASSIS 12

H03714-10

–

Fill bleeding syringe

with the appropriate hydraulic fluid.

Syringe (50329050000)
Brake fluid DOT 4 / DOT 5.1 (

p. 155)

–

On the slave cylinder, remove the protection cap and bleeder
screw

and mount bleeding syringe

S04456-10

–

Now press the fluid into the system until it emerges from
hole

of the master cylinder without bubbles.

–

Occasionally extract the fluid from the master cylinder reser-

voir to prevent overflowing.

–

Remove the bleeding syringe. Mount and tighten the bleeder

screw. Mount the protection cap.

–

Correct the fluid level of the hydraulic clutch.
Guideline

Fluid level below container

rim

4 mm (0.16 in)

–

Position the cover with the membrane. Mount and tighten the

screws.

Info

Use water to immediately clean up any brake fluid that

has overflowed or spilled.

12.44

Removing the engine guard

H01655-01

–

Remove screws

and engine guard.

12.45

Installing the engine guard

H01655-01

–

Attach the engine guard on the frame at the rear and swing

up at the front.

–

Mount and tighten screws

Guideline

Remaining screws,

chassis

10 Nm (7.4 lbf ft)

Содержание TE 250










































































































































































Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды

Husqvarna TE 250, Руководство пользователя

Результаты поиска

Содержание TE 250

Отзывы:

Похожие инструкции для TE 250

Бренды по названию

Популярные бренды