Husqvarna Solar Mower, Руководство оператора, Страница: 11 / 16

English –
9
USE
Settings
The keyboard is used to deactivate the theft alarm, enter the
security code and to change the value of some of the Solar
Mower’s parameters.
If you have started to enter a value via the keyboard and wish to
cancel the input, press
*
.
Basic setting
You can simplify the operation of the mower by entering
*
9 #
*
code #. This switches off the theft alarm, so there is no need to
enter the first digit of the code when you lift the cover. This also
switches off all audible signals, except the start-up beep.
Choice of personal code
Your Solar Mower requires the code to be entered for it to
function. On delivery the code is set to
*
0000 # . It is however
possible to select your own personal code, which of course is
recommended. Select a code consisting of four digits and then
enter the following from the keyboard:
*
current code # new code # new code #.
Example: To change the from code 0000 to 1234:
*
0000 # 1234 # 1234 #
The green LED will come on after entering the sequence if the
Solar Mower accepts the input.
NOTE! It is important that you write down your personal code
and keep it in a safe place. If you do forget your personal code,
contact your dealer.
Regular entry of the code
Your personal code must be entered periodically and in this way
the solar mower is unusable if it is stolen. The solar mower
signals that there is no code when it is time to re-enter the code.
Note you do not need to change your code only enter it.
The code must be entered once per week under the default
setting, but you can choose a time interval from 1 to 26 weeks
by pressing:
*
6 # no. of weeks #
*
code #
Example:
*
6 # 5 #
*
code # means that you must enter the
code every fifth week.
The code must also be entered if the theft alarm is tripped or if
the solar mower is switched off.
Setting the sound
The sounds the Solar Mower uses are divided into five groups:
Operating sound The Solar Mower indicates it is mowing or
charging.
Error sound The Solar Mower indicates that something
is wrong.
Night sound The Solar Mower indicates it is in the idle
mode due to a lack of sunlight.
Theft alarm Comes on when the Solar Mower is not
switched off correctly.
Start-up sound The Solar Mower warns you that the
cutting disc is about to start.
The volume of the following sounds can be set individually.
Operating sound
*
2 # volume # (default volume 1)
Error sound
*
3 # volume # (default volume 1)
Night sound
*
1 # volume # (default volume 1)
Start-up sound
*
4 # volume # (default volume 2)
The volume is set between 0 and 4, where 0 = silent and 4 =
the highest volume. The theft alarm always has the highest
volume when on.
Theft alarm
Under the default setting the theft alarm sounds for 1 minute. It
is possible to set how long the theft alarm shall sound using the
command:
*
7 # number of minutes #
*
code #
Example:
*
7 # 10 #
*
code # sounds the theft alarm for ten
minutes.
*
7 # 0 #
*
code # shuts the alarm off completely. The number
of minutes can be set between 0 - 1000. The theft alarm always
has the highest volume when on.
If you have a small lawn
IMPORTANT INFORMATION
Your Solar Mower is technically capable of working day
and night, and is set to do so on delivery. It is not
recommended that it is used in this way, however. If it
works longer than necessary the lawn may look
downtrodden. This would also subject the Solar Mower
to unnecessary wear and shorten the life of the battery.
The Solar Mower works as soon as there is sufficient daylight. If
the Solar Mower is used on a small area it may mean that it
works more than is necessary to keep the lawn mown. To avoid
this it is possible to limit the operating time by entering:
*
8 # maximum operating time in hours #
The operating time can be selected from 1 - 10, where 1 - 9
sets the limit for the maximum number of operating hours per
day. 10 means unlimited operation. Note it is the maximum
number of hours that is set. The actual operating time varies
depending on the available light and the cutting resistance. The
correct setting will vary from garden to garden. Try different
operating times until you get a satisfactory result.
When the Solar Mower has mown for the set number of hours
LED 2 flashes when the rear solar panel is lifted. The Solar
Mower will not start to mow again until night has passed.
Resetting
Pressing
*
21 # returns all settings to their default values set
when the Solar Mower was delivered. However, your personal
code will not be changed.
Searching for a buried boundary wire
The Solar Mower has a feature that will easily find a buried
boundary wire. Enter
*
5 # 1 # and the Solar Mower will be set
to look for the boundary wire.
Move the Solar Mower, with the rear solar panel folded up,
towards the area where the boundary wire has been buried.
When the Solar Mower gives off a signal the boundary wire is
directly under the sensor at the front of the Solar Mower. The
command only works when the generator is connected. If the
mower cannot detect any signal, all four LEDs will flash.
Reset the Solar Mower to normal operation by entering
*
5 # 0 # , or fold down the rear solar panel.
ON
STOP
3
4
5
6
1 2 3 4
5 6 7 8
9 0
#
1
2