manualshive.com logo in svg

Husqvarna Rider 215TX, Руководство оператора, Страница: 29 / 32

Поделиться
Скачать
Husqvarna Rider 215TX Скачать руководство пользователя страница 29

English

 – 29

Technical data

Note 1: The power rating of the engine indicated is the average net output (at specified rpm) of a typical production engine for the engine model measured to SAE 
standard J1349/ISO1585. Mass production engines may differ from this value. Actual power output for the engine installed on the final machine will depend on the 
operating speed, environmental conditions and other values.

Note 2: Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive 2000/14/EC.

Note 3: Noise pressure level according to EN 836. Reported data for noise pressure level has a typical statistical dispersion (standard deviation) of 1.2 dB(A).

Note 4: Vibration level according to EN 836. Reported data for vibration level has a typical statistical dispersion (standard deviation) of 0.2 m/s

2

 (steering wheel) and 

0.8 m/s

2

 (seat).

Dimensions

Rider 215TX

Length with cutting unit, mm/ft

223 / 7,32

Length without cutting unit, mm/ft

194 / 6,36

Width with cutting unit, mm/ft

100-108 / 3,28-3,54

Width without cutting unit, mm/ft

89 / 2,92

Height, mm/ft

1070/3,52

Operating weight with cutting deck, kg/lb

247-255 / 546-562

Wheel base, mm/ft

887/2,91

Track width, front, mm/ft

712/2,34

Track width, rear, mm/ft

627/2,06

Tyre dimensions

16 x 6,50 x 8

Air pressure, rear - front, kPa / bar / PSI

60 (0,6/8,5)

Engine

Brand / Model

Briggs & Stratton

Nominal engine output, kW (see note 1)

12,8

Displacement, cm

3

/cu.in

656

Fuel, minimum octane grade lead-free

85

Tank volume, litres/USqt

12/13

Oil

SAE 5W/30 or SAE 10W/30

Oil tank capacity, litre

1,4

Starting

Electric start 12V

Max.motor speed, r/min

3100 

±

 100

Electrical system

Type

12 V, negative earthed

Battery

12 V, 24 Ah

Spark plug

Electrode gap, mm/inch

0,75/0,030

Noise emissions and cutting width 

(see note 2)

Sound power level, measured dB (A)

97

Sound power level, guaranteed dB(A)

98

Cutting width, cm/inch

94-103-112/37-41-44

Sound levels

(see note 3)

Sound pressure level at the operators ear, dB(A)

82

Vibration levels

(see note 4)

Vibration level on the steering wheel, m/s

2

2,5

Vibration level in the seat, m/s

2

0,7

Transmission

Brand

Tuff Torq

Oil, class SF-CC

SAE 10W/40

Forward speed, km/h.

0-9,5

Reverse speed, km/h

0-9,5

Cutting unit

Type

Combi 94

Combi 103

Содержание Rider 215TX

































Отзывы:

Нет отзывов