Husqvarna RIDER 1030 BIOCLIP Скачать руководство пользователя | Manualshive

Страница: 19 / 46

background image

18

– English

Reparation instructions

13

2

3

8

7

5

6

10

9

4

2

14

11

12

1

Replacing steering wires

1
Release the steering wires' rear attachment (1).

2
Release the steering wires' front attachment (2) at
the steering transmission chain (6) and pull the
steering wires out throught the frame.

Note. If the old wires are still complete, the new

wires can be attached to the old ones when they
are pulled out through the frame, the new wires
will then come automatically into place.

3
Attach the new wires.

Once the new wires are in place, check the wire
tension (see page 17).

Removal/installation of steering axle

1
Release the steering wires' rear attachment (1).

Remove the frame plate (see page 17).

2
Remove the steering wheel and steering column by
releasing the lock nut and unscrewing the locking
screw, lift the steering wheel and steering column
upwards.

3
Remove the two steering wheel rod carriers (3).

4
Remove the steering wheel rod circlip (4).

5
Pull the steering axle (5) upwards and move the
lower part of the axle backwards to remove the
steering transmission chain (6).

6
Move the upper bearing (7) uppwards until it goes
free from the steering axle (5). If the bearing is to
be replaced, the bushing (8) must be knocked out
of the bearing.

Eng-Verk Riders

97-04-28, 16.47

18

«
...
17
18
19
20
21
...
»

Содержание RIDER 1030 BIOCLIP















































Отзывы:

Нет отзывов

Похожие инструкции для RIDER 1030 BIOCLIP

Бренд: Vari Страницы: 42

Бренд: Poulan Pro Страницы: 48

Бренд: Toro Страницы: 60

18.5HP Z-Force 42

Бренд: Cub Cadet Страницы: 56

Z Master Professional 5000 Series

Бренд: Toro Страницы: 80

Бренд: Lastec Страницы: 21

Бренд: SaMASZ Страницы: 36

Бренд: COMPANION Страницы: 76

Бренд: Exmark Страницы: 5

Бренд: Worx Nitro Страницы: 75

Бренд: Honda Страницы: 24

Бренд: Ego Power+ Страницы: 444

Бренд: Snapper Страницы: 72

Бренд: Husqvarna Страницы: 47

Бренд: Husqvarna Страницы: 64

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды