Husqvarna GTH2548XP Скачать руководство пользователя | Manualshive

Страница: 30 / 48

background image

30

Engine continues to run

1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not

when operator leaves seat

corrected, contact an authorized service center/

with attachment clutch

department.

engaged

Poor cut - uneven

1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

  2.   Mower deck not level.     2.   Level mower deck.
  3.   Buildup of grass, leaves, and trash under mower.    3.   Clean underside of mower housing.
  4.   Bent blade mandrel.     4.   Replace blade mandrel.
  5.   Clogged mower deck vent holes from buildup of     5.   Clean around mandrels to open vent holes.
   grass, leaves, and trash around mandrels.

Mower blades will not

1. Obstruction in clutch mechanism. 1. Remove obstruction.

rotate

2. Worn/damaged mower drive belt. 2. Replace mower drive belt.

3. Frozen idler pulley. 3. Replace idler pulley.
4. Frozen blade mandrel. 4. Replace blade mandrel.

Poor grass discharge

1. Engine speed too slow. 1. Place throttle control in “FAST” position.

  2.   Travel speed too fast.       2.   Shift to slower speed.
  3.   Wet grass.        3.   Allow grass to dry before mowing.
  4.   Mower deck not level.     4.   Level mower deck.
  5.   Low/uneven tire air pressure.   5.    Check tires for proper air pressure.
  6.   Worn, bent or loose blade.     6.   Replace/sharpen blade.  Tighten blade bolt.
  7.   Buildup of grass, leaves and trash under mower.      7.   Clean underside of mower housing.
  8.   Mower drive belt worn.   8.   Replace mower drive belt.
  9.   Blades improperly installed.   9.   Reinstall blades sharp edge down.
  10.   Improper blades used.     10.    Replace with blades listed in this manual.
  11.   Clogged mower deck vent holes from buildup of     11.   Clean around mandrels to open vent holes.
   grass, leaves, and trash around mandrels.

Headlight(s) not working

1. Switch is “OFF”. 1. Turn switch “ON”.

(if so equipped)

2. Bulb(s) or lamp(s) burned out. 2. Replace bulb(s) or lamp(s).

  3.   Faulty light switch.      3.   Check/replace light switch.
  4.   Loose or damaged wiring.    4.    Check wiring and connections.
  5.   Blown fuse.       5.   Replace fuse.

Battery will not charge

1. Bad battery cell(s). 1. Replace battery.

  2.   Poor cable connections.   2.   Check/clean all connections.
  3.   Faulty regulator (if so equipped).     3.   Replace regulator.
  4.   Faulty alternator.        4.   Replace alternator.

Loss of drive

1. Freewheel control in “disengaged” position. 1. Place freewheel control in “engaged” position.

  2.   Motion drive belt worn, damaged, or broken.   2.   Replace motion drive belt.
  3.   Air trapped in transmission during shipment     3.   Purge transmission.
   or servicing.

Engine “backfi res”

1. Engine throttle control not set at “SLOW” 1. Move throttle control to “SLOW” position and allow

when turning engine

position for 30 seconds before stopping engine. to idle for 30 seconds before stopping engine.

“OFF”

PROBLEM

CAUSE CORRECTION

TROUBLESHOOTING POINTS

«
...
28
29
30
31
32
...
»

Содержание GTH2548XP

















































Отзывы:

Нет отзывов

Похожие инструкции для GTH2548XP

EC Hydro Midsize

Бренд: Ransomes Страницы: 150

YARD-MAN Series 556

Бренд: Yard-Man Страницы: 20

Craftsman 944.601181

Бренд: Sears Страницы: 52

Бренд: Scag Power Equipment Страницы: 41

Бренд: Elem Garden Technic Страницы: 91

Бренд: Yardworks Страницы: 7

Бренд: Yardworks Страницы: 25

Бренд: Makita Страницы: 116

Бренд: Yard-Man Страницы: 20

Бренд: Kraftixx Страницы: 246

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 48

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды